14
To Clean Hot Water/Steam Spout:
Always clean the hot water/steam spout after use to avoid the
build-up of milk residues and prevent it from clogging.
1.
Place a container under the hot water/steam spout and let a
little fresh water out. See "Delivering Hot Water" section. Stop
delivery by pressing
STOP
.
2.
Wait a few minutes for the hot water/steam spout to cool
down. When cool, remove the spout. Hold the spout steady
with one hand and with the other, turn and detach the
cappuccino maker, pulling it downwards.
3.
Also remove the steam connection nozzle by pulling it
downward. Check that the hole in the connection nozzle is not
blocked. If necessary, clean using a toothpick.
4.
Wash all parts of the spout thoroughly with a sponge and
warm water. Attach the connection nozzle and the cappuccino
maker onto the spout by pushing it upwards and turning it
clockwise until it is secure.
Delivering Hot Water
1.
Make sure the hot water/steam spout is attached correctly to
the hot water/steam connection nozzle.
2.
Place a container under the spout as close as possible to
avoid splashes.
3.
Select
HOT WATER from the home page. The
corresponding image appears on the display, together with a
progress bar which fills gradually as preparation proceeds.
4.
The machine delivers hot water, then the delivery stops
automatically. To interrupt hot water delivery manually,
press
STOP
.
NOTES:
■
If "Energy Saving" mode is active, there may be a few seconds
delay before hot water is delivered.
■
Preparation of hot water can be customized. See "Customizing
Beverages" and "Memorizing Your Personal Profile" sections.
Steam Delivery
1.
Make sure the hot water/steam spout is attached correctly to
the hot water/steam connection nozzle. Fill a container with
the liquid to be heated or frothed and immerse the hot water/
steam spout in the liquid.
2.
Select
STEAM from the homepage. The corresponding
image appears on the display, together with a progress bar
which fills gradually as preparation proceeds and after a few
seconds, steam to heat the liquid is delivered from the hot
water/steam spout.
3.
When the required temperature or level of froth is reached,
interrupt steam delivery by pressing
STOP
.
Tips for using steam to froth milk:
■
When choosing the size of the container, bear in mind that the
liquid doubles or triples in volume.
■
For a richer, denser froth, use skimmed or partially skimmed
milk at refrigerator temperature.
■
For a creamier froth, rotate the container with a slow
movements in a upward motion.
■
To avoid milk with poor froth or large bubbles, always clean
the spout.
COFFEE SYSTEM CARE
General Cleaning
To avoid damage to the coffee system, do not use solvents or
abrasive detergents to clean the coffee system. Use a soft damp
cloth to clean the exterior of the coffee system. Clean all machine
parts regularly.
IMPORTANT:
Before any cleaning, turn the coffee system off
using the main On/Off switch and unplug it.
IMPORTANT:
Do not immerse the coffee system in water.
Cleaning the Coffee Grounds Container and Drip Tray
When the display shows the message EMPTY GROUNDS
CONTAINER, the grounds container must be emptied and
cleaned. The appliance cannot be used to make coffee until the
container is has been cleaned. Even if it is not full, the empty
grounds container message is displayed 72 hours after the first
coffee has been prepared. For the 72 hours to be calculated
correctly, the machine must never be turned off with the main
switch.
1.
Open the bottom door by rotating it downwards and open.
A
A. Hot water/steam spout
PUSH
04-Mar-2019 07:49:57 EST | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
