JENCO 6010N Operation Manual Download Page 3

 

2

GENERAL INTRODUCTION   

 

 

Thank you for selecting the 6010N meter. The 6010N is a precision 
tool that measure pH, ORP and temperature. A built-in 
microprocessor stores, calculates and compensates for all 
parameters related to pH determinations including pH electrode 
temperature characteristics, electrode slope deviations and buffer 
solutions. 
 
This unit has a waterproof IP65 case. The touch mode keys are 
highly reliable with tactile and audio feedback. This meter can 
operated with one 9V battery, typical battery life is 1000 hours. 
Re-calibration is not required when power is turned on again. 
 
The front of the meter has a large LCD that displays pH or ORP and 
temperature simultaneously along with user prompts and mode 
indicators. The unit prompts the user through calibration and 
measurement procedures. 
 
An AUTOLOCK feature for both pH and ORP measurements 
enables the unit to automatically sense the end point and “ HOLD ” 
the display to indicate the end point value of a measurement. 
AUTOLOCK and user prompts help eliminate most errors in 
determining pH and mV values, resulting in precise, repeatable and 
error-free measurements. The 6010N can also be used in 
non-AUTOLOCK mode.   
 
The model 6010N is available with pH, ORP and ATC (Automatic 
Temperature Compensation) probes. Other features include 
electrode offset recognition, electrode slope recognition, electrode 
efficiency display, built-in buffer coefficients, automatic or manual 
temperature compensation, long battery life, and 50/60Hz AC noise 
rejection. This meter is user-friendly, for field, industrial and 
laboratory applications. 
 

INITIAL INSPECTION     

 

 

Carefully unpack the unit and accessories. Inspect for damages 
made in shipment. If any damage is found, notify your 

Jenco

 

representative immediately. All packing materials should be saved 
until satisfactory operation is confirmed. 
 

WATER PROOF   

 

 

Though the 6010N meter is housed in a watertight case, 

DO NOT

 

use it underwater. The watertight case prevents permanent damage 
to the unit if accidentally dropped into non-corrosive solutions.   

Summary of Contents for 6010N



















Reviews: