background image

- 2 -                                Jema Autolifte A/S wheel balancer DWC 

 

 

WHEEL BALANCER INSTRUCTION MANUAL 

DWC 

 

 

ATTENTION 

 

This manual is an integral part of the product. 

The warnings and instructions in this manual provide important information about SAFETY IN USE and MAINTENANCE and 

should be read very carefully. 

KEEP THIS MANUAL IN A SAFE PLACE SO THAT IT IS ON HAND FOR REFERENCE. 

 

Product destination   

The wheel balancing machine is designed exclusively for balancing the tires of wheels with maximum dimensions defined in the 

general section of this manual. 

During  ordinary  maintenance  of  the  apparatus,  it  is  the  responsibility  of  the  maintenance  operator  (who  should  be  suitably 

trained  and  professionally  qualified)  to  turn  the  main  switch  to  OFF,  ensuring  that  it  cannot  be  accidentally  switched  on, 

unplugging the connection to the power supply if necessary. 

This machine should only be used for the purpose for which it was designed. Any other use is to be considered improper and 

unreasonable. 

The  manufacturer  (Balance)  may  not  be  considered  responsible  for  any  damage  caused  by  improper,  incorrect  and 

unreasonable use. 

 

Training and information for the machine operators   

The machine should only be used by specially trained and authorized personnel. 

The training and informing of the operating staff should be done so as to enable them to operate the machine as described in 

the instructions provided by the manufacturer, so that the machine performs in the best possible way and the operations are 

carried out efficiently and safely. 

For any doubts relating to the use, installation and maintenance of the machine, please refer to the instructions manual or if 

necessary contact the authorized service centers or the technical services office of Balance. 

 

Transport and unpacking   

For transport of the packaged product, refer to Fig.1. 

Once  the  product  has  been  unpacked,  check  that  the  instructions 

manual is there, that the material is complete and there are no parts 

which have been visibly damaged. 

Remove  the  contents  of  the  packages  and  place  them  in  a storage 

area inaccessible to children or animals. 

 

Environmental requirements for installation 

The site of installation should have the following features: 

 

Level horizontal floor, rigid, preferably concrete or tiled.                                                               

Fig. 1 

 

Sufficient lighting (but without dazzling or very bright lights). 

 

Protected from atmospheric conditions. 

 

Pollution-free area. 

 

Noise level lower than provided for by current regulations. 

 

The work place must not be exposed to dangerous movements from other machines in operation. 

 

Explosive, corrosive and/or toxic materials should not be stored in the same place. 

Summary of Contents for DWC





















Reviews: