manualshive.com logo in svg

Jelight JEL-2400, Operating Instructions Manual, Page: 7 / 22

Share
Download
Jelight JEL-2400 Operating Instructions Manual Download Page 7

 

Page 7 

4. 

Internal Battery Pack: 

 

4A. About:

 

The  JEL-2400  contains  a  3.7V  5500mAh  rechargeable  lithium-polymer  battery  pack. A 
new,  fully  charged  battery  pack  will  typically  provide  4-8  hours  of  continuous  use 
(depending on display brightness settings and other feature settings).  

 

4B. Charging: 

Charging the battery is done through the USB 3.0 mini or micro port. 

 

 

WARNING:

 The battery pack in the JEL-2400 is expected to last for many years (up to 500 charge 

cycles).  Batteries should only be charged, stored and used in temperature between 0 Deg C to 45 
Deg C, or expansion and damage can occur.  Battery packs should only be replaced by trained 
personnel. Changing of the battery pack by end user voids the warranty and can cause damage to 
the pc board.

 

 

The  power  source  can  be  supplied  from  a  computer,  a  power  bank,  a charging hub,  a 
wall-wart or any USB 2.0 or 3.0 device. A full charge is obtained in approximately 12 - 14 
hours.  Meter will charges the fastest when the power  button is in the off position. The 
JEL-2400  circuit  is  design  to  prevent  over  charge.  The  JEL-2400  has  a  low  power 
indicator that will advise when the battery needs recharging. 

 

 
 
5. Sensor Connector and Wiring:

 

 
The 15 pin D Sub miniature connector on the top of the JEL-2400 was selected to allow 
backwards  compatibility  with  existing  D  sensors.  Future  JEL-2400  sensors  will  be 
supplied  with  an  internal  memory  chip  inside  the  D-sub  connector  that  includes  the 
model and serial number of the sensor as well as calibration information. The JEL-2400 
will  have  the  ability  to  read  the  smart  detector  information  and  apply  the  proper 
calibration factor to be used during testing.  

 

 

The D-sub not only receives the current generated by the sensor after exposure to light, 
it  also  supplies  reverse  5  or  9  volt  bias  to  sensors  requiring  bias  for  power  and/or  to 
improve  response  time.   The D sub connector  is not limited to only measuring devices 
manufactured by Jelight. Any solid state device that generates current from 50 pA to 1 
mA  can  be  connected  to  the  JEL-2400  for  measurement  of  current.  Please  see  wiring 
diagram below: 

 
 

 

 

 

 

 

Summary of Contents for JEL-2400























Reviews:

No comments