JEI MAGBEAST HM200T Operator'S Manual Download Page 18

Page: 18 / 18

MAGBEAST HM200T

18 |

P a g e

WARRANTY CARD

WARRANTY CARD No

.............

..................................................................... in the name of Manufacturer warrants the

Magbeast 5 Drilling Machine with Magnetic Base to be free of defects in material and

workmanship under normal use for a period of 12 months from date of sale.

This warranty does not cover cutters, damage or wear that arise from misuse, accident,

tempering or any other causes not related to defects in workmanship or material.

Date of production.........................................................................................................

Serial number ...............................................................................................................

Date of sale ...................................................................................................................

Signature of seller .........................................................................................................

4 / 2

February 2023

WE RESERVE THE RIGHT TO MAKE CORRECTIONS

AND MODIFICATIONS IN THIS MANUAL WITHOUT PRIOR NOTICE

Summary of Contents for MAGBEAST HM200T



















Search results

Summary of Contents for MAGBEAST HM200T

Reviews:

Related manuals for MAGBEAST HM200T

Brands by name

Popular brands

JEI MAGBEAST HM200T, Operator'S Manual

Search results

Summary of Contents for MAGBEAST HM200T

Reviews:

Related manuals for MAGBEAST HM200T

Brands by name

Popular brands