background image

5.1.

tweeter installation – dashboard:

I

nsert tweeter bowl instead of the air valves in the dashboard:

(This does not affect the ventilation)

5.1.1.

remove the lid of the air valve

5.1.2.

drill a small hole into the ventilation duct for the speaker cable

5.1.3.

connect tweeter with cable (1,5 - 4 mm

2

) and lead the speaker

    cable to the mount of the crossover in the dashboard (see speaker
    connection on (s. page 6 / 6.1.).

5.1.4. install the tweeter with the mounting bowl supplied with and affix it

    with a hexagon head screw M4x8 and secure with washer. Connect

    the tweeter and affix the mounting bowl either with hot melt adhesive
    or insert the clamp into the air valve.

5.2.

installation of midrange – dashboard

Install the midrange into the original mount in the dashboard:

5.2.1.

lever off the speaker grill and remove the original installed speaker.

5.2.2.

connect the JEHNERT midrange with speaker cable (1,5 - 4 mm

2

).

Lead the speaker cable to the mount of the cross over in the dashboard.

(see speaker connection (s. page 6 / 6.1.).

5.2.3.

install the midrange with mounting ring into the original mount and

     affix as the factory installed midrange.

6.1. Installation of crossover circuit:

recommendation:

          mount of crossover in the dashboard near the steering system respectively
          the glove box

6.2. Loudspeaker cables

6.2.1. lead 1x speaker cable  (1,5 - 4 mm

2

) from amplifier to crossover

           in the dashboard.

6.2.2. lead the speaker cable  (1,5 - 4 mm

2

) from crossover into the car doors

           (see wiring diagram on page 11)

tip:

 please observe that air duct for the central locking system is kept

                 open and movable (rubber grommet between bearer and door).
                 Air duct may knick if closing the door!

6.2.3. adapt set of cables supplied with to the speaker connection.

5.

Tweeter and midrange Installation / loudspeaker cables

6. crossover circuit / loudspeaker cables

       76150 - AUDI 80  Convertible/coupé

- 7 -

© JEHNERT SOUND DESIGN

      76150 - AUDI 80  Convertible/coupé

- 8 -

© JEHNERT SOUND DESIGN

75150

6.3. Insulation of the door lining / car doors

Not necessary!

Summary of Contents for AUDI 80 convertible

















Reviews: