background image

Removing the grills:

The Velcro fasteners stick together very strongly!
The grills can be removed anytime by carefully lifting them off.
Please, avoid any way of forceful yanking at the grills.
It could break!

9.3.

9.2.

Our Tip:

        If the panel cannot be pressed on completely at some points. . .

       Cause:

the special form at these points and the resulting differences in
material cross section of the grill.

       Solution:

the distance can be levelled out with spacers  3  under the
Velcro disc.

(Spacers included with the screw kit)

9.1. Precisely align and carefully press grill into the Velcro fasteners.

    The Velcro fastener makes a crackling sound
    when it is closed correctly.

1.1.

roll down window completely

1.2.

remove the door handle 

(1)

:

unscrew the 3 screws 

(A-C)

 under the door handle (are different according

to year of construction, cross head screws or socket head cap screws)

tip – door handle fastening with socket head cap screws:

the socket head cap screws are difficult to unscrew, check the correct

movable point by turning the screw and pulling the door handle.

1.3.

for vehicles with »electric window control«:

push the switch board out of the guide groove in the door handle and

unplug the cables

please observe:

some cables on this plug are permanent current

carrying and not protected by fuses.

                                    Short circuits may damage the window electronic!!

1.4.

unscrew the screw on the door latch lever 

(3)

 and remove the door latch lever.

1.5.

remove the adhesive tape underneath the sheet metal clamp (fastening for

       the cover of the Bowden pull wire). Hang out the Bowden pull wire for the
       door latch.

1.6.

remove the chromium cover and the guide contact on the outer door side 

(2)

1.7.

pull the door-lining upward away from the inner door metal

A

B

C

1 .  Disassembly of the door lining

       76150 - AUDI 80  Convertible/coupé

- 3 -

© JEHNERT SOUND DESIGN

76150 - AUDI 80  Convertible/coupé

- 12 -

© JEHNERT SOUND DESIGN

9. Installation of the speaker’s grill:

         grill

2   self-adhesive Velcro-strip

1   Velcro fastener

3   Washer M4 ø 20 as spacer

doorpanel

75150

Summary of Contents for AUDI 80 convertible

















Reviews: