JEHNERT SOUND DESIGN 65740 Assembly Instruction Manual Download Page 2

Page: 2 / 12

Assembly instruction

Status: 06.05.2022

Art.- No. 65740

Mercedes Sprinter

W907 / W910

from 2018, Cab System

Cable routing / connection scheme 3-way without amp+ subwoofer

Crossover

MHT crossover vehicle-speciﬁ c

Mounted behind the A-pillar trim on the side of the
dashboard cavity.

Center Speaker

Tweeter »XE 26«
Mounting in the dashboard in the mid-high module,
pre-installed.

Midrange »XE 80«
Mounting in the dashboard in the mid-high module,
pre-installed.

Woofer »XM 165«
Mounting in the vehicle door panels.

radio

General installation instructions - must be observed!

Radio settings:

To achieve the best sound, all settings on the radio (bass, treble, loudness,

equalizing, etc.) should be set to ZERO or OFF.

Installation Notice:

To avoid vibration noise, secure all cable harnesses with insulating tape or

similar.

Summary of Contents for 65740













Search results

Summary of Contents for 65740

Reviews:

Related manuals for 65740

Brands by name

Popular brands

JEHNERT SOUND DESIGN 65740, Assembly Instruction Manual

Search results

Summary of Contents for 65740

Reviews:

Related manuals for 65740

Brands by name

Popular brands