USER MANUAL
JEFCIND270L-10.0
270L
BELT DRIVEN AIR COMPRESSOR
•
10HP
•
10Bar
•
415V
~
50Hz (3)
USER MANUAL
JEFCIND270L-10.0
270L
BELT DRIVEN AIR COMPRESSOR
•
10HP
•
10Bar
•
415V
~
50Hz (3)
www.jeffersontools.com
www.jeffersontools.com
14
15
Inspecting / Replacing a Worn Compressor Belt
•
If your air compressor is equipped with a protective cage, find the screws or clips that hold the cover in place and remove them.
•
Inspect the belt and check for cracks or signs of wear.
•
If replacement is necessary, move onto the next step. Otherwise, replace the cage / belt guard and repeat the inspection as scheduled.
•
To remove the worn / damaged belt, grasp it firmly and while pulling it over the large pulley, rotate the pulleys by hand and the belt will
remove from all pulleys.
•
Take the new belt, place it over the small pulley and work it onto the large pulley by hand-turning it in a forward motion until it is securely on
the large pulley. Replace the cage / belt guard.
TROUBLESHOOTING
FAULT
CAUSE
REMEDY
Tank pressure continually drops.
Air leak, check all connections.
Locate and rectify leak.
Tank pressure won’t build up.
Drain valve is open.
Close tank drain valve.
The compressor won’t switch off.
The safety valve blows off.
Pressure switch fails to stop motor Faulty pressure
switch.
Contact a specialized service technician.
Tank pressure won’t build up and the pump
is getting hotter than normal, inlet suction
is poor.
The compressor head gasket or valve plate is faulty.
Contact a specialized service technician.
There is a leak from the base of the
pressure switch when the compressor is
running.
Failure of the pressure relief valve. (Located in the base
of pressure switch).
Contact a specialized service technician.
There is a leak from the base of the
pressure switch when the compressor is
stopped.
The Non Return Valve (from the tank) is leaking.
Disassemble and clean if necessary replace valve insert.
The compressor is noisy with metallic
clangs.
Bearing or loose part problem.
Stop the compressor and contact a specialized service
technician.
The compressor sounds like it is trying to
start (motor makes a humming noise).
Air pressure trapped on piston is resisting the starting
effort.
Turn unit off and on again using the pressure switch. This
will vent air from the delivery tube.
The compressor sounds like it is trying to
start (motor makes a humming noise).
The capacitor is faulty.
Stop the compressor and contact a specialized service
technician.
Air leaks from the safety valve at pressures
less than 10 bar.
The safety valve is faulty.
Replace the Safety valve.
13. WEEE Waste Electrical and Electronic Equipment Statement
Information on Disposal for Users of Waste Electrical & Electronic
Equipment
This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should
not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to
designated collection points where it will be accepted free of charge.
For private households:
Dispose of this product at the end of its working life and in compliance with the EU Directive on Waste Electrical and Electronic
Equipment (WEEE). Contact your local solid waste authority for recycling information for this equipment.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the
environment, which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with you national legislation.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard this product please contact your local authorities or dealer and ask for the
correct method of disposal.
ENVIRONMENTAL PROTECTION
Recycle any packaging and unwanted materials instead of disposing of them as waste. All tools, accessories and packaging
should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable, reaches the end of its working life and requires disposal, drain off any
fluids (if applicable) into approved containers and dispose of the product and the fluids according to local regulations.
