background image

9

USER MANUAL 

v2.1

JEFWASPGRO65HP

6.5HP Gearbox Petrol Washer

www.jeffersontools.com

 

 

  EQUIPMENT SETUP

1. Attaching the Spray Gun to the High Pressure Hose:  

• 

Pull the slip ring on the female quick-disconnect fitting back on the high 
pressure hose (See

 Fig 9

). 

• 

Insert the male quick-fitting on the spray gun into the female socket on the 
high pressure hose. 

• 

Release the slip ring on the female disconnect and twist. Listen for a 
"

click

" to ensure both of the quick fittings have been coupled correctly 

• 

Pull the high pressure hose and spray gun in opposite directions to ensure 
that they do not separate under pressure.

2. Connecting the Spray Lance to the Spray Gun: 

• 

Thread the spray lance on to the spray gun until secure (See 

Fig 10

)

3. Connect the Hose and Water Supply to the Pump

 

Attach the other end of the high pressure hose to the high pressure outlet on 
the pump. Pull down on the collar of the quick release fitting and slide onto the 
pump and let go of the collar. 

Pull on the hose to ensure of a tight connection.  (See 

Fig 11

.)

Before connecting the hose to the water supply ensure that the filter screen is 
clean and remove any dirt or debris found. 

Replace the filter if it is damaged. (See 

Fig 12

). Connect to the supply. 

Run water through the hose for 30 seconds to remove any dirt before 
connecting. 

Important:

 

Do not syphon any standing water to use for the water supply. Use 

only cold running water from mains supply (no more than 100°F)  

Connect the hose (it should not exceed 50ft in length) to the water inlet on the 
pressure washer. Tighten by hand until secure. 

Turn on the water. Squeeze the trigger to purge the pump system of air an 
impurities. (See 

Fig 13

).

Warning: 

Do not attempt to crank or start the engine before it has 

been properly serviced with the recommended oil. This can lead to 
engine failure and void your warranty. 

Note: 

There must be at least 10ft (3m) of unrestricted hose between 

the washer inlet and any fittings such as a vacuum breaker or check 
valve. 

9.

10.

11.

12.

13.

Summary of Contents for 6.5HP

































Reviews: