background image

14

USER MANUAL 

v2.1

JEFWASPGRO65HP

6.5HP Gearbox Petrol Washer

www.jeffersontools.com

  USING CHEMICALS & DETERGENTS

Chemical Cleaning:

Spray the chemicals onto a dry surface using the procedures outlined 
in previous sections. Start at the lower portion of the cleaning area and 
working upwards, using long, even, overlapping strokes.  (See 

Fig 23

.).

Always ensure that the filter is fully submerged in the cleaning solution at 
all times.

Allow the detergent to soak in for 3-5 minutes before washing and 
rinsing. 

Re-apply as needed to prevent the surface from drying. Do not allow the 
detergent to dry on to the cleaning surface to prevent streaking. 

Note: Detergent cannot be applied with the high pressure spray tips 
(white, green, yellow or red)

After Chemical Cleaning:

Important:

 

You will need to flush the detergent siphoning system after each use by placing the filter into a bucket of 

clean water then run the pressure washer in low pressure for 1-2 minutes.   

After using chemicals, soaps and detergents it is necessary to thoroughly clean the pressure washer. 

Place the chemical hose in a container of clean water. 

Turn on the pressure washer and hold the trigger on the spray gun top draw clean water through the system to clean 
it thoroughly. 

  MAINTENANCE

To ensure efficient operation and longer life of your pressure washer a routine maintenance schedule should be 
prepared and followed. If the equipment is used in unusual conditions such as high-temperature or dusty conditions 
more frequent maintenance checks will be required.   

Warning: 

Before performing any maintenance be aware that the equipment should be completely shutdown, 

depressurised and allowed to cool down. This will ensure that no injuries can be sustained by moving parts, 
water pressure or hot surfaces. 

The fuel tank contains flammable fuel do not smoke near or work near naked flames while 
maintaining this equipment. 

Please note: All repairs should be carried out by Jefferson approved engineers. All replacement parts 
should be supplied or recommended by Jefferson. Any unapproved repairs or modifications will 
invalidate the warranty. 

22.

23.

Summary of Contents for 6.5HP

































Reviews: