background image

TABLE OF CONTENTS

1.0

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.1

SYSTEM COVERAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.2

SIX-STEP TROUBLESHOOTING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . .1

2.0

IDENTIFICATION OF SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3.0

SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . .1

3.1

AIRBAG SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3.1.1

PASSENGER AIRBAG ON-OFF SWITCH . . . . . . . . . . . . . . . . . . . . . . . .2

3.1.2

SPECIAL TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3.1.3

DIAGNOSTIC TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3.1.3.1 ACTIVE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3.1.3.2 STORED CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3.2

AUDIO SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3.2.1

SATELLITE RADIO (SDARS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3.3

ELECTROCHROMIC COMPASS/TEMPERATURE MIRROR WITH LIGHTS . . . .4

3.4

ELECTRICALLY HEATED SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.4.1

REAR WINDOW DEFOGGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.5

ELECTRO/MECHANICAL INSTRUMENT CLUSTER (EMIC) . . . . . . . . . . . . . . . . .7

3.5.1

SMART CLUSTER FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.5.2

INSTRUMENT CLUSTER SELF TEST. . . . . . . . . . . . . . . . . . . . . . . . . . .8

3.6

VEHICLE COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

3.7

USING THE DRBIII

T

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3.7.1

DRBIII

T

ERROR MESSAGES AND BLANK SCREEN . . . . . . . . . . . . .10

3.7.2

DRBIII

T

DOES NOT POWER UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3.7.3

DISPLAY IS NOT VISIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.0

DISCLAIMERS, SAFETY, WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.1

DISCLAIMERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.2

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.2.1

TECHNICIAN SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . .10

4.2.2

VEHICLE PREPARATION FOR TESTING . . . . . . . . . . . . . . . . . . . . . . .11

4.2.3

SERVICING SUB-ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.2.4

DRBIII

T

SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.3

WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.3.1

VEHICLE DAMAGE WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.3.2

ROAD TESTING A COMPLAINT VEHICLE . . . . . . . . . . . . . . . . . . . . . .11

5.0

REQUIRED TOOLS AND EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6.0

GLOSSARY OF TERMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

7.0

DIAGNOSTIC INFORMATION AND PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . .13

AIRBAG
ACCELEROMETER 1 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
INTERNAL 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
OUTPUT DRIVER 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
SAFING SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
STORED ENERGY FIRING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
STORED ENERGY LOGIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

i

Summary of Contents for Wrangler TJ 2006

























































































































































































































Reviews: