background image

SERVICE MANUAL

VM117, VM137

EN - 9813/3300 - ISSUE 1 - 09/2015

This manual contains original instructions, verified by
the manufacturer (or their authorized representative).

Copyright 2015 © JCB SERVICE

All rights reserved. No part of this publication may

be reproduced, stored in a retrieval system, or

transmitted in any form or by any other means,

electronic, mechanical, photocopying or otherwise,

without prior permission from JCB SERVICE.

www.jcb.com

Foreword

The Operator's Manual

You and others can be killed or seriously injured

if  you  operate  or  maintain  the  machine  without

first  studying  the  Operator's  Manual.  You  must

understand  and  follow  the  instructions  in  the

Operator's  Manual.  If  you  do  not  understand

anything,  ask  your  employer  or  JCB  dealer  to

explain it.

Do not operate the machine without an Operator's

Manual, or if there is anything on the machine you

do not understand.

Treat the Operator's Manual as part of the machine.

Keep  it  clean  and  in  good  condition.  Replace  the

Operator's Manual immediately if it is lost, damaged

or becomes unreadable.

Contents

01 - Machine
06 - Body and Framework
09 - Operator Station
15 - Engine
18 - Fuel and Exhaust System
21 - Cooling System
24 - Brakes
25 - Steering System
27 - Driveline
30 - Hydraulic System
33 - Electrical System
72 - Fasteners and Fixings
75 - Consumable Products
78 - After Sales

Summary of Contents for VM117




















































Reviews: