background image

Safety

  It is imperative to follow safety guidelines to prevent electric 
  shock, injury, fire or explosion. 

- Do not use the units for any purpose other than PCB preheating. Incorrect use may cause a fire.

- The mains cable must be plugged into approved bases. Make sure that it is properly grounded 
  before use. When unplugging it, hold the plug, not the wire.

- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflammable products to ignite.

- Heat can cause inflammable products to ignite even when out of sight.

- Be careful with the remains of liquid tin. In contact with the skin, it can cause burns.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the smoke produced when soldering.

-  Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working 

to avoid personal harm.

-  This appliance can be used by children over the age of eight as well as persons with reduced physical, 

sensory or mental capabilities or lacking experience provided that they have been given adequate 
supervision or instruction concerning the use of the appliance and understand the hazards involved. 
Children must not play with the appliance. 

- Maintenance must not be carried out by children unless supervised.

Maintenance

Before carrying out maintenance or storage, always allow the equipment and the support to cool 
down.

- Check periodically that the Pre Heater and

the Support are clean - especially the
support sliding guides axes.

 
- Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.

- Only if it is absolutely necessary and if cleaning with isopropyl alcohol (IPA) is not enough, it is 

recommended to use a scraper to remove dirt in the glass area.

- Replace any defective or damaged parts. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

- Replace a blown fuse as follows:

Fuse Holder

Fuse

Fuse Holder

Remove the fuse holder by turning the 
holder counter-clockwise with a flat head 
screwdriver. 

Remove the worn fuse and and replace it with 
a new one. Reinstall the fuse holder into the 
preheater by screwing it in clockwise.

14

Sliding 

Guide 

Axes

Summary of Contents for PHBE





















Reviews: