background image

25

JCB-MS-254SB
Instruction & User Manual

Maintenance

Prior to any adjustment, maintenance or ser-
vice work disconnect the mains power plug!

WARNING!

General maintenance measures

 

Wipe chips and dust off the machine from 

time to time using a cloth. In order to 

extend the service life of the tool, oil the 

rotary parts once monthly. Do not oil the 

motor.

 

When cleaning the plastic do not use 
corrosive products.

Brush inspection

Check the carbon brushes after the first 50 

operating hours with a new machine, or when 

new brushes have been fitted. After carrying 

out the first check, repeat the check every 10 

operating hours.
If the carbon is worn to a length of 6 mm, 

or if the spring or contact wire are burned 

or damaged, it is necessary to replace both 

brushes. If the brushes are found to be usable 

following removal, it is possible to reinstall 
them.

Service information

Please note that the following parts of this 
product are subject to normal or natural wear 
and that the following parts are therefore also 
required for use as consumables.
Wear parts*: Carbon brush, saw blade, table 
inserts, dust bags, batteries,
* Not necessarily included in the scope of 
delivery!

Electrical connection

The electrical motor installed is connected and 
ready for operation. The connection complies 
with the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the 
extension cable used must also comply with 
these regulations.

 

 The product meets the requirements of                 
EN62841-3-9 and is subject to special 
connection conditions. This means that 
use of the product at any freely selectable 
connection point is not allowed.

 

 Given unfavorable conditions in the power 
supply the product can cause the voltage to 
fluctuate temporarily.

 

 The product is exclusively intended for use 
at connection points that have a continuous 
current-carrying capacity of at least 100 A 
per phase.

 

As the user, you are required to ensure, 
in consultation with your electric power 
company if necessary, that the connection 
point at which you wish to operate the 
product meets the specified requirements.
Kinks where the connection cable has been 
improperly fastened or routed.

Important information

In the event of an overloading the motor will 
switch itself off. After a cool-down period (time 
varies) the motor can be switched back on 
again.

Maintenace and electrical connection

All manuals and user guides at all-guides.com

Summary of Contents for MS-254SB

































Reviews: