background image

7

JCB-MS-254SB
Instruction & User Manual

 

 

Use of the power tool for operations 

Unrestrained or moving workpieces could 
be thrown at high speeds, causing injury.

different from intended could result in a 
hazardous situation.

Slippery handles and grasping surfaces do 
not allow for safe handling and control of 
the tool in unexpected situations.

these instructions and in the manner 
intended for the particular type of 
power tool, taking into account the 
working conditions and the work to 
be performed.

h

Keep handles and grasping surfaces dry, 
clean and free from oil and grease.

3

The workpiece must be stationary and 
clamped or held against both the fence and
the table. Do not feed the workpiece into 
the blade or cut “freehand” in any way.

Cutting on the pull stroke is likely to 
cause the saw blade to climb on top of 
the workpiece and violently throw the 
blade assembly towards the operator.

4

Push the saw through the workpiece. Do 
not pull the saw through the workpiece. 
To make a cut, raise the saw head and pull 
it out over the workpiece without cutting, 
start the motor, press the saw head down 
and push the saw through the workpiece.

Supporting the workpiece“cross handed” 
i.e. holding the workpiece to the right of
the saw blade with your left hand or vice 
versa is very dang erous.

5

Never cross your hand over the intended 
line of cutting either in front or behind the
saw blade.

The proximity of the spinning saw blade 
to your hand may not be obvious and 
you may be seriously injured.

6

Do not reach behind the fence with either 
hand closer than 100 mm from either side 
of the saw blade, to remove wood scraps, 
or for any other reason while the blade is
spinning.

Bent or warped workpieces can twist or 
shift and may cause binding on the 
spinning saw blade while cutting. There 

7

Inspect your workpiece before cutting. If 
the workpiece is bowed or warped, clamp 
it with the outside bowed face toward the 
fence. Always make certain that there is 
no gap between the workpiece, fence and 
table along the line of the cut

5

Service

1

Mitre saws are intended to cut wood or 
wood-like products, they cannot be used 
with abrasive cut-off wheels for cutting 
ferrous material such as bars, rods, studs, 
etc.

SAFETY INSTRUCTIONS FOR MITRE SAWS

a

Have your power tool serviced by a 
qualified repair person using only identical
replacement parts.

 
 

This will ensure that the safety of the 
power tool is maintained.

Abrasive dust causes moving parts such as 
the lower guard to jam. Sparks from 
abrasive cutting will burn the lower guard, 
the kerf insert and other plastic parts.

If your hand is placed too close to the saw 
blade, there is an increased risk of injury 

2

Use clamps to support the workpiece 
whenever possible. If supporting the 
workpiece by hand, you must always keep 
your hand at least 100 mm from either 
side of the saw blade. Do not use this saw 
to cut pieces that are too small to be 
securely clamped or held by hand.

 

from blade contact.

All manuals and user guides at all-guides.com

Summary of Contents for MS-254SB

































Reviews: