background image

13

JCB-MS-305SB-L
Instruction & User Manual

NOISE INFORMATION

Total noise values determined in accordance with IEC 62841  

A-Weighted Sound Pressure (L

pA

)

90.7 dB(A)

Uncertainty K

pA

3 dB

A-Weighted Sound Level (L

wA

)

107.3 dB(A)

Uncertainty K

wA

3 dB

Wear ear protection when sound pressure is over 80 dB(A)

Wear hearing protection. 
The effects of noise can cause a loss of 

hearing. The above-mentioned noise emission 

values were measured in accordance with a 

standardised test procedure and can be used to 

compare one power tool with another. 
The above-mentioned noise emission values 

can also be used for the preliminary assessment 

of exposure. 
Warning: 
The noise emissions during the actual use of 

the power tool may differ from the above-

mentioned values depending on the power 

tool being used, in particular on the type 

of workpiece being processed. Try to keep 

emissions as low as possible, for example by 

limiting your working time. In this regard, all 

the operational cycle phases must be taken into 

consideration (such as the times when the tool 

is switched off or running idle). 

WARNING!

Summary of Contents for JCB-MS-305SB-L






























Reviews: