background image

JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092  

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

Safety Warnings Common 

for Grinding or Abrasive 

Cutting-Off Operations:

1. This power tool is intended to 
function as a grinder, or cut-off 
tool. Read all safety warnings, 
instructions, illustrations and 
specifications provided with 
this power tool.

 Failure to follow 

all instructions listed below may 
result in electric shock, fire and/or 
serious injury.

2. Operations such as sanding, 
wire brushing, polishing are not 
recommended to be performed 
with this power tool. 

Operations 

for which the power tool was not 
designed may create a hazard and 
cause personal injury.
3. 

Do not use accessories which 

are not specifically designed 
and recommended by the tool 
manufacturer.

 Just because the 

accessory can be attached to your 
power tool, it does not assure safe 
operation.

4. The rated speed of the 
accessory must be at least equal 
to the maximum speed marked 
on the power tool. 

Accessories 

running faster than their rated 
speed can break and fly apart.

5. The outside diameter and the 
thickness of your accessory must 
be within the capacity rating of 
your power tool. 

Incorrectly sized 

accessories cannot be adequately 

guarded or controlled.

6. The arbour size of discs, 
flanges, backing pads or any 
other accessory must properly 
fit the spindle of the power tool.

 

Accessories with arbour holes 
that do not match the mounting 
hardware of the power tool will run 
out of balance, vibrate excessively 
and may cause loss of control.

7. Do not use a damaged 
accessory. Before each use 
inspect the accessory such as 
abrasive discs for chips and 
cracks, backing pad for cracks, 
tear or excess wear. If power 
tool or accessory is dropped, 
inspect for damage or install 
an undamaged accessory. After 
inspecting and installing an 
accessory, position yourself and 
bystanders away from the plane 
of the rotating accessory and 
run the power tool at maximum 
no-load speed for one minute. 

Damaged accessories will normally 
break apart during this test time.

8. Wear personal protective 
equipment. Depending on 
application, use face shield, 
safety goggles or safety glasses. 
As appropriate, wear dust mask, 
hearing protectors, gloves 
and workshop apron capable 
of stopping small abrasive or 
workpiece fragments.

 The eye 

protection must be capable of 
stopping flying debris generated 

Summary of Contents for JCB-AG720





























Reviews: