background image

31

JCB-20BLMS
Instruction & User Manual

GENERAL CERTIFICATE OF CONFORMITY

PRODUCT(S) COVERED BY THIS CERTIFICATE: 

USA/CA No. JCB-20BLMS

UK/EU No. JCB-18BLMS

Manufacturer No. BLCY-237

Amazon ASIN No. N/A

CITATION TO EACH CONSUMER PRODUCT SAFETY REGULATION TO WHICH THIS 

PRODUCT IS BEING CERTIFIED:

IEC 62841-1:2014

IEC 62841-3-9:2015+A11

IEC 55014-2:2015

IEC 55014-1:2017

IDENTIFICATION DETAILS OF IMPORTER/US DOMESTIC MANUFACTURER 

CERTIFYING PRODUCT COMPLIANCE:

Name: JCB Tools (Yellow and Black Tools Limited)

Address: 55 Romsey Industrial Estate

Romsey, SO51 0HR

UK

Tel no: +44 1794 834250

CONTACT INFORMATION OF INDIVIDUAL MAINTAINING RECORDS OF TEST 

RESULTS:

Name: Tim Burgoyne, QA Technical Manager & Compliance Officer 

Address: 55 Romsey Industrial Estate,  Romsey, SO51 0HR, UK

Email: [email protected]

Tel no: +44 1794 834250

DATE AND PLACE WHERE THIS PRODUCT WAS MANUFACTURED:

Date: mm/yyyy

Address: Ningbo Hanpu Tools Co. Ltd. Hengxi Industrial Area,

Yinzhou, Ningbo, P. R. China

DATE AND PLACE WHERE THIS PRODUCT WAS TESTED FOR COMPLIANCE:

Date: 11/2019

Name: TÜV Rheinland (Shanghai) Co., Ltd.

Address: Shanghai, 200072, P. R. China

Tel no: +86 21 61081188

IDENTIFICATION OF THIRD-PARTY LABORATORY ON WHOSE TESTING THE 

CERTIFICATE DEPENDS:

Name: TÜV Rheinland

Address: Am Grauen Stein

51105 Köln, Germany

Tel no: +49 221 8060

Summary of Contents for JCB-20BLMS
































Reviews: