background image

17

JCB-20BLMS
Instruction & User Manual

OPERATING INSTRUCTIONS

Intended Use

The drag, crosscut and mitre saw is designed 
to crosscut wood and plastic respective of the 
machine’s size. The saw is not designed for 
cutting firewood.

The equipment is to be used only for its 
prescribed purpose. Any other use is deemed 
to be a case of misuse. The user / operator 
and not the manufacturer will be liable for any 
damage or injuries of any kind caused as a 
result of this.
The equipment is to be operated only with 
suitable saw blades. It is prohibited to use any 
type of cutting-off wheel.
To use the equipment properly you must also 
observe the safety information, the assembly 
instructions and the operating instructions to be 
found in this manual.
All persons who use and service the equipment 
have to be acquainted with this manual and 
must be informed about the equipment’s 
potential hazards. It is also imperative to 
observe the accident prevention regulations in 
force in your area. The same applies for the 
general rules of health and safety at work. 

The manufacturer will not be liable for any 
changes made to the equipment nor for any 
damage resulting from such changes. Even 
when the equipment is used as prescribed it 
is still impossible to eliminate certain residual 
risk factors. The following hazards may arise 
in connection with the machine’s construction 
and design:

 

m

Contact with the saw blade in the 
uncovered saw zone.

 

m

Reaching into the running saw blade (cut 
injuries).

 

m

Kick-back of workpieces and parts of 
workpieces.

 

m

Saw blade fracturing.

 

m

Catapulting of faulty carbide tips from the 
saw blade.

 

m

Damage to hearing if ear-defenders are not 
used as necessary.

 

m

Harmful emissions of wood or plastic dust 
when used in closed rooms.

Do not use the saw to cut materials other
than those specified described in manual.

WARNING!

The supplied saw blade is only intended for
the sawing of wood! Do not use this blade
for the sawing of plastic!

WARNING!

Summary of Contents for JCB-20BLMS
































Reviews: