background image

20

Please consult your manual for full information or consult your local dealer.

Battery isolator

The battery isolator switch is used to disconnect the 
battery from the machine electrics. The switch must 
be turned to the off position if any maintenance 
work is to be performed on the machine.

Some machine systems perform shut down 
cycles after the engine stops. Wait until shut 
down cycles are complete before setting the 
battery isolator switch to the off position.

The Battery must be isolated at the end of a 
working cycle or if the machine is being left 
unattended and the lights are not required.

Disconnect

If the machine has an electronically controlled 
engine, you must wait a period of time before 
you isolate the battery. This is to allow the ECM 
(Engine Control Module) to shutdown correctly. 
The time period starts when you turn the ignition 
off. Check the isolator switch label and the 
operators manual for the correct time period.

In the event of an emergency, remove the 
isolator key without waiting.

1. 

 Wait for the specified duration after the 
engine is turned off before you isolate the 
battery (30 s).

2. 

Make the machine safe.

3. 

Turn the ignition key to the off position.

4. 

 Wait for the engine ECM to shutdown 
correctly (if installed).

5. 

Get access to the isolator key.

6. 

 Turn the battery isolator key in the indicated 
direction and remove.

Connect

Before you start the engine or use the machine 
electrics, the battery isolator key must be installed 
and switched on.

1.   

Make sure the ignition is set to off.

2.   

Insert the battery isolator key and turn in the 
indicated direction.

A

B

Fig 9

Battery Isolator (where fitted)
A

  Battery

B

  Isolator switch 

Summary of Contents for G70RS

































Reviews: