background image

 03 - Attachments, Couplings and Load Handling

 00 - Attachments

 00 - General

03 - 3

9813/9600-2

03 - 3

00 - General

Introduction 

......................................................

 03-3

Health and Safety 

...........................................

 03-4

Check (Condition) 

............................................

 03-4

Introduction

A wide range of optional attachments are available

to increase the versatility of your machine. Only JCB

approved  attachments  are  recommended  for  use

with your machine. Consult your JCB Distributor for

the full list of approved attachments available.

Some  attachments  are  supplied  complete  with

instructions  on  safety,  installing  and  removing,

operation  and  maintenance.  Read  and  fully

understand the information before fitting, using and

servicing the attachment. If there is anything you do

not understand, ask your JCB Distributor.

Before  using  any  attachment,  read  Working  With

The Machine in the Operator Manual and consider

how  the  attachment  is  going  to  affect  operational

safety.  With  the  attachment  installed,  there  may

be  changes  in  the  machine's  centre  of  gravity  or

overall dimensions. This could have an effect on, for

example, machine stability, the gradients on which it

is safe to operate or the safe distance from power

lines.

Practice using attachments off the job before working

with them for the first time.

JCB  attachments  are  designed  and  manufactured

specifically to suit the machine's hydraulic system,

mounting arrangements and safe load requirements.

Attachments  which  are  not  designed  for  use  with

this machine may cause damage and create safety

hazards for which JCB cannot be held responsible.

In  addition  the  machine's  warranty  and  any  other

legislative compliance may be affected by the use of

non JCB approved attachments.

If your machine needs the hydraulic system adapting

to  facilitate  the  use  of  auxiliary  attachments,  you

must consult your distributor. Only suitably qualified

personnel must reroute hydraulic hoses.

All  optional  attachments  will  have  limits  on  their

operation. i.e. lifting capacity, speeds, hydraulic flow

rates,  etc.  Always  check  in  the  literature  supplied

with the attachment or in the Specification section of

this manual. Some specification limits may also be

displayed on the attachments Data/Rating Plate.

Important: Do not operate or work with attachments

until the machine hydraulic oil has reached its normal

working temperature.

Summary of Contents for 210X




















































Reviews: