background image

 01 - Machine

 06 - About this Manual

 06 - Using the Manual

01 - 17

9813/9600-2

01 - 17

Use the applicable Servicemaster diagnostics

tools. Refer to (PIL 33-57-03).

To  help  you  reference  the  applicable  information

as quickly as possible refer to Fault Finding in this

section. Tables are given for the primary fault types.

Applicable  cross  references  are  then  given  to  the

specific fault finding, check procedures and systems

descriptions.

Remove and Install

Before removal of components or assemblies, clean

the  applicable  parts  of  the  machine.  After  removal

cap open ports and hoses to prevent contamination.

Refer to (PIL 01-33-00).

Use new sealing elements such as gaskets and O-

rings.

Do not install defective components or assemblies. if

necessary replace them with new ones.

Dismantle and Assemble

Before dismantling an assembly clean it.

After  dismantling,  clean  the  individual  components

and check them for wear and defects. If necessary

replace them with new ones.

During assembly use new sealing elements such as

gaskets and O-rings.

Torque Tightening

Use  the  torque  tightening  values  contained  in

the  individual  procedures  (Remove  and  Install,

Disassemble  and  Assemble  etc.).  If  no  values  are

specified, use the standard torque tightening values.

Refer to (PIL 72-00).

Always use the correct grade of fastener.

Consumable Products

Some  procedures  require  the  use  of  consumable

products  such  as  lubricants,  sealants,  adhesives

and locking fluids. Use the correct products. Where

products are available from JCB the applicable part

numbers are given in the procedures. A complete list

of consumable products available from JCB is given

in this manual. Refer to (PIL 75-00).

After Sales

Some  procedures  require  the  use  of  equipment

such as special tools and PPE (Personal Protective

Equipment). Where special tools are available from

JCB  the  applicable  part  numbers  are  given  in  the

procedures. Full details about the applicable special

tools are given in this manual. Refer to (PIL 78-00).

Use  the  correct  PPE  to  comply  with  local  and

employer regulations.

Summary of Contents for 210X




















































Reviews: