18z-1, 19c-1, 19c-1 EP
12
13
Please see operator manual for full details.
Foot Controls & Dozer Lever
Swing Controls – 18z-1, 19c-1
Auxiliary Controls – 18z-1, 19c-1
Dozer Lever
Retracting Undercarriage Lever
Fig 15
Fig 16
Fig 17
Fig 18
Operation
Operating Levers/Pedals
80
9831/2900-1
80
Swing
Figure 62. 16C-1 and 18Z-1
A
B
B
A
A
Swing left
B
Swing right
To swing the boom to your left, push the swing pedal to the left side. Release the pedal when the excavator
end has reached the required position.
To swing the boom to your right, push the swing pedal to the right side. Release the pedal when the excavator
end has reached the required position.
Figure 63. 19C-1
A
B
B
A
C
D
A
Swing left
B
Swing right
C
Thumb wheel
D
Change over button
Press the change over button on the left joystick to select swing mode. An icon is displayed on the instrument
panel.
Press the change over button on the left joystick to select swing mode. An icon is displayed on the instrument
panel. To swing the boom to your left move the thumb wheel on the right joystick to the left. Release the thumb
wheel when the excavator end has reached the desired position.
To swing the boom to your right move the thumb wheel on the right joystick to the right. Release the thumb
wheel when the excavator end has reached the desired position.
Operation
Operating Levers/Pedals
82
9831/2900-1
82
Figure 65.
B
C
B
B
C
C
A
A
Track extension lever
B
Upward- retract
C
Downward- extend
Auxiliary Circuit Controls
WARNING
Before operating the auxiliary control system make sure that you are aware of all safety notices
that apply to the attachment you are using. Also make sure you have installed the attachment correctly and
have read its operator's manual.
Notice:
The auxiliary hydraulic circuit a single acting system as standard with optional double acting
system available. If applicable make sure that the single/double acting control is correctly configured for
your attachment before operating it otherwise machine damage could occur.
Push the auxiliary pedal to the left or right depending on the attachment installed and the function required. In
single acting mode, oil flow only in one direction. So pressing the pedal to left will lead to feed line and pressing
the pedal to right will lead to the return line while in double acting mode pushing the pedal to left or right lead
to feed line or return line. Refer to the operator manual supplied with the attachment.
Figure 66. 16C-1 and 18Z-1
A
A
Auxiliary pedal
Electro-proportional Controls
Attachments are operated using the joysticks.
Use the auxiliary switch on the console to select either single acting or double acting high flow/low flow
operation. Check the instrument panel.
Operation
Operating Levers/Pedals
81
9831/2900-1
81
Dozer Blade Controls
Notice:
Before operating the dozer blade, make sure that large rocks or other objects will not jam the dozer
mechanism.
The dozer is operated by a single control lever on the right side of the cab.
Refer to: Operator Station.
The lever is spring loaded to the central position. In this position the dozer will not move.
To raise the dozer pull the lever backwards. At the required position release the lever.
To lower the dozer push the lever forward until an increased resistance is felt and the blade moves. At the
required position release the lever. Refer to Figure 64.
Figure 64.
A
B
A
B
C
A
Lower the dozer
B
Raise the dozer
C
Control lever
Extending Undercarriage Controls
To extend or retract the undercarriage (option):
1. Stop the machine on level ground.
2. Make sure that all persons are away from the machine and the surrounding area.
3. Operate the dozer control lever to lower the dozer blade and lift the tracks just off the ground.
Refer to: Dozer Blade Controls.
4. Operate the excavator controls to slew the machine to specified degrees.
Angle: 180°
5. Operate the excavator controls to lower the excavator arm and lift the rear tracks just off the ground. Refer
to Figure 65.
6. Operate the track extension control lever to move the undercarriage to the required position. Refer to Figure
65.
6.1. Move the lever upward to extend the undercarriage. Both tracks will extend together.
6.2. Move the lever downward to retract the undercarriage. Both tracks will retract together.
Operation
Operating Levers/Pedals
82
9831/2900-1
82
Figure 65.
B
C
B
B
C
C
A
A
Track extension lever
B
Upward- retract
C
Downward- extend
Auxiliary Circuit Controls
WARNING
Before operating the auxiliary control system make sure that you are aware of all safety notices
that apply to the attachment you are using. Also make sure you have installed the attachment correctly and
have read its operator's manual.
Notice:
The auxiliary hydraulic circuit a single acting system as standard with optional double acting
system available. If applicable make sure that the single/double acting control is correctly configured for
your attachment before operating it otherwise machine damage could occur.
Push the auxiliary pedal to the left or right depending on the attachment installed and the function required. In
single acting mode, oil flow only in one direction. So pressing the pedal to left will lead to feed line and pressing
the pedal to right will lead to the return line while in double acting mode pushing the pedal to left or right lead
to feed line or return line. Refer to the operator manual supplied with the attachment.
Figure 66. 16C-1 and 18Z-1
A
A
Auxiliary pedal
Electro-proportional Controls
Attachments are operated using the joysticks.
Use the auxiliary switch on the console to select either single acting or double acting high flow/low flow
operation. Check the instrument panel.
A
Swing left
B
Swing right
A
Auxiliary pedal
A
Lower the dozer
B
Raise the dozer
C
Control lever
A
Track Extension Lever
B
Upward - Retract
C
Downward - Extend
Operation
Operating Levers/Pedals
82
9831/2900-1
82
Figure 65.
B
C
B
B
C
C
A
A
Track extension lever
B
Upward- retract
C
Downward- extend
Auxiliary Circuit Controls
WARNING
Before operating the auxiliary control system make sure that you are aware of all safety notices
that apply to the attachment you are using. Also make sure you have installed the attachment correctly and
have read its operator's manual.
Notice:
The auxiliary hydraulic circuit a single acting system as standard with optional double acting
system available. If applicable make sure that the single/double acting control is correctly configured for
your attachment before operating it otherwise machine damage could occur.
Push the auxiliary pedal to the left or right depending on the attachment installed and the function required. In
single acting mode, oil flow only in one direction. So pressing the pedal to left will lead to feed line and pressing
the pedal to right will lead to the return line while in double acting mode pushing the pedal to left or right lead
to feed line or return line. Refer to the operator manual supplied with the attachment.
Figure 66. 16C-1 and 18Z-1
A
A
Auxiliary pedal
Electro-proportional Controls
Attachments are operated using the joysticks.
Use the auxiliary switch on the console to select either single acting or double acting high flow/low flow
operation. Check the instrument panel.
Instrument Panel
A
Fuel level guage
B
Warning and indicator lamps
Fig 13
Fig 14
Instrument Panel – 19c-1 EP
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
Engine pre-heat
Coolant temperature
Engine oil pressure
Battery charging
Service due warning
Low fuel indicator
Seat belt
High speed travel
SAE active
Master warning
Immobilisers active
Hydraulics active
Quick hitch unlock
Lift overload warning
Aux 1 – double acting
Aux 1 – single acting
Aux 2 – low flow
Swing active
Operation
Instruments
70
9831/2900-1
70
Instruments
General
Indicators for the engine and related systems are mounted in the instrument cluster in the right hand console.
Instrument Panel
For: 16C-1, 18Z-1 ..................................................................................................................... Page 70
For: 19C-1 ................................................................................................................................ Page 71
(For: 16C-1, 18Z-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Figure 50.
B
A
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Operation
Instruments
70
9831/2900-1
70
Instruments
General
Indicators for the engine and related systems are mounted in the instrument cluster in the right hand console.
Instrument Panel
For: 16C-1, 18Z-1 ..................................................................................................................... Page 70
For: 19C-1 ................................................................................................................................ Page 71
(For: 16C-1, 18Z-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Figure 50.
B
A
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
71
9831/2900-1
71
Warning and Indicator Lamps
Figure 51.
A
B
C
D
E
F
G
H
J
K
L
M
N
Table 8.
A
Engine pre-heat
Illuminate green when engine pre-heater is active.
B
Coolant temperature
Illuminate red when coolant temperature exceeds the pre-set value.
C
Engine oil pressure
Illuminate red when oil pressure drop too low. Illuminate when the ignition
switch is set to position "I" before starting the engine but should be extin-
guish when the engine starts. If remains 'ON' then stop the engine immedi-
ately and contact your JCB Dealer.
D
Battery charging condi-
tion
Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is
not charging while engine is running. If battery is charging, the lamp and
buzzer should go off a few seconds after the engine is started.
E
Service due warning
Illuminate amber when service is due.
F
Fuel indicator
Illuminate white when fuel level is low.
G
Seat belt
Visual. Illuminate red if the seat belt is not fastened or the operator is not
sitting on the seat.
H
High travel speed
Illuminate green when high travel speed is selected.
J
SAE (Society of Auto-
motive Engineers) ac-
tive
Illuminate green when SAE is active.
K
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
L
Immobilisers active
Visual. Illuminate amber when immobiliser armed function is active.
M
Hydraulic active
Illuminate green when hydraulic services is active.
N
Aux 1 (single acting,
high flow)
Illuminate green when single acting (high flow) is active.
(For: 19C-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Operation
Instruments
70
9831/2900-1
70
Instruments
General
Indicators for the engine and related systems are mounted in the instrument cluster in the right hand console.
Instrument Panel
For: 16C-1, 18Z-1 ..................................................................................................................... Page 70
For: 19C-1 ................................................................................................................................ Page 71
(For: 16C-1, 18Z-1)
The gauges, warning and indicator lamps are grouped together on the instrument cluster. When a warning
lamp comes on, an alarm will sound.
Figure 50.
B
A
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
Operation
Instruments
72
9831/2900-1
72
Figure 52.
A
B
A
Fuel level gauge
B
Warning and indicator lamps
Fuel level: The needle position shows the fuel level.
Warning and Indicator Lamps
Figure 53.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
Table 9.
A
Master warning
Audible/Visual. If amber light illuminate then contact JCB dealer. If red light
illuminate then stop the machine immediately and contact your JCB dealer.
B
Quickhitch unlock
Illuminate amber when quickhitch is unlocked.
