background image

 01 - Machine

 03 - Safety

 21 - Worksite Safety

01 - 10

9813/6750-1

01 - 10

21 - Worksite Safety
Introduction

WARNING

 You or others can be killed or seriously

injured if you do unfamiliar operations without first

practising them. Practise away from the worksite

on a clear area. Keep other people away. Do not

perform new operations until you are sure you can

do them safely.

WARNING

 There could be dangerous materials

such as asbestos, poisonous chemicals or other

harmful  substances  buried  on  the  site.  If  you

uncover any containers or you see any signs of

toxic waste, stop the machine and advise the site

manager immediately.

WARNING

 Before you start using the machine,

check with your local gas company if there are

any buried gas pipes on the site.
If there are buried gas pipes we recommend that

you ask the gas company for any specific advice

regarding the way you must work on the site.
Some modern gas pipes cannot be detected by

metal detectors, so it is essential that an accurate

map of buried gas pipes is obtained before any

excavation work commences.
Hand  dig  trial  holes  to  obtain  precise  pipe

locations.  Any  cast  iron  pipes  found  must  be

assumed to be gas pipes until contrary evidence

is obtained.
Older  gas  pipes  can  be  damaged  by  heavy

vehicles driving over the ground above them.
Leaking gas is highly explosive.
If a gas leak is suspected, contact the local gas

company immediately and warn all personnel on

the site. Ban smoking, make sure that all naked

lights are extinguished and switch off any engines

which may be running.
You are strongly advised to make sure that the

safety arrangements on site comply with the local

laws and regulations concerning work near buried

gas pipes.

CAUTION

  Before  you  start  using  the  machine,

check with your local public water supplier if there

are buried pipes and drains on the site. If there

are, obtain a map of their locations and follow the

advice given by the water supplier.
You are strongly advised to make sure that the

safety arrangements on site comply with the local

laws and regulations concerning work near buried

pipes and drains.

CAUTION

 If you cut through a fibre optic cable,

Do not look into the end of it, your eyes could be

permanently damaged.

An  applicable  worksite  organisation  is  required  in

order  to  minimise  hazards  that  are  caused  by

restricted  visibility.  The  worksite  organisation  is  a

collection of rules and procedures that coordinates

the  machines  and  people  that  work  together  in

the  same  area.  Examples  of  worksite  organisation

include:

Restricted areas

Controlled patterns of machine movement

A system of communication.

You and/or your company could be legally liable for

any damage you may cause to public utilities. It is

your responsibility to make sure that you know the

locations of any public utility cables or pipes on the

worksite which could be damaged by your machine.

Summary of Contents for 135




















































Reviews: