background image

Important Safety Instructions

2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN!

DO NOT EXPOSE

TO RAIN OR MOISTURE!

ATTENTION

RISQUE DE CHOC ÉLECTRIQUE

NE PAS ENLEVER!

NE PAS EXPOSER Á

LA PLUIE NI Á L'HUMIDITÉ!

Explanation of Graphic Symbols

The exclamation point within an equilateral triangle is
intended to alert the users to the presence of impor-
tant operating and maintenance (servicing) instruc-
tions in the literature accompanying the product.

The lightning flash with the arrowhead symbol, with-
in an equilateral triangle, is to alert the user to the
presence of insulated “dangerous voltage” within the
products enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to humans.

CAUTION: TO REDUCE THE RISK OF ELECTRONIC
SHOCK - DO NOT REMOVE COVER. NO USER SER-
VICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED PERSONNEL. DO NOT EXPOSE THIS APPA-
RATUS TO RAIN OR MOISTURE.

ATTENTION: POUR EVITER LES RISQUES DE CHOC
ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE.
AUCUN ENTRETIEN DE PIECES INTERIEURES PAR
L’USAGER. CONFIER L’ENTRETIEN AU PERSONNEL
QUALIFIE. AVIS: POUR EVITER LES RISQUES D’IN-
CENDIE OU D’ELECTROCUTION, N’EXPOSEZ PAS CET
ARTICLE A LA PLUIE OU A L’HUMIDITE.

1.

Read These Instructions

- Before operating your new JBL product,

please read safety and operating instructions.

2.

Keep These Instructions

- For future reference and troubleshooting 

purposes, retain these instructions.

3.

Heed All Warnings 

- All warnings in this manual should be followed.

4.

Follow All Instructions

5.

Water and Moisture

- This product is intended for indoor use only. Do 

not use this apparatus near water or plumbing fixtures.

6.

Cleaning

- Do not use any solvent based cleaners on the finish. To 

clean enclosure, turn off speaker and disconnect power cord then 
clean only with a lint-free cloth moistened with water.

7.

Ventilation

- Do not block any ventilation openings, including the Linear 

Dynamics Aperture Port on the monitor systems. Install these products in 
accordance with manufacturers instructions. Do not install near any 
heat sources such as radiators, heat registers, stoves or other
apparatus that produce heat.

8.

Grounding and Power Cords

- Protect the power cord from being 

walked-on or pinched, particularly at the plug’s convenience recepti-
cle and the point where it connects to the apparatus. Do not defeat 
the safety purpose of the grounding type plug. The power cord sup-
plied with your powered product has a plug with 2 blades plus a 3rd 
grounding prong. Do not cut off or damage the grounding prong. If the 
provided plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.

All powered products are fitted with a detachable power cord
(supplied) which connects to the chassis AC connector. The power 
cord has an IEC female connector on one end and a male mains con-
nector on the other end. This cord is supplied specifically to accom-
modate the different safety and electrical code requirements of indi-
vidual countries. If you are traveling abroad with your system, test the 
power mains and be aware of any specific voltage requirements 
before operating your system.

9.

Options

- Only use attachments or accessories specified by JBL 

Professional.

10.

Wall or Ceiling Mounting

- The appliance should be mounted on a 

wall or ceiling only as recommended by the manufacturer. Caution:
Unsafe mounting or overhead suspension of any heavy load can result 
in serious injury and equipment damage. Mounting of speakers should 
be done by qualified persons in accordance with all applicable local 
safety and construction standards. Be certain to follow the instructions 
provided by the manufacturer of the mounting bracket. Before select-
ing a mounting bracket, be certain that it is capable of supporting the 
weight of the speaker to be mounted.

11.

Non-use Periods

- Unplug this apparatus during lightning storms or 

when it will be unused for long periods of time.

12.

Servicing

- Refer all servicing to qualified service personnel. Servicing 

is required when the apparatus does not operate normally or has been 
damaged in any way, including: power supply cord or plug is dam-
aged, water or other liquid has been spilled or objects have fallen into 
the apparatus.

13.

Carts and Stands

- The appliance should be used 

only with carts or stands that are sturdy and well 
balanced. All appliance and cart combinations 
should be moved with care. Quick stops, excessive 
force, and uneven surfaces may cause the appliance 
and cart combination to overturn.

14.

Fire

- No naked flame sources, such as lighted candles, should be 

placed on the surface, of the apparatus.

15.

Coupler

- The appliance coupler is used as the disconnect device, and 

the appliance coupler shall remain readily operable.

The information contained in this document is confidential and the
copyright of JBL Professional. To convey its contents, in part of it
whole, to any party without prior written authorization is a violation of
the copyright. © JBL Professional 2003

Summary of Contents for LSR6300 Series

























Reviews: