background image

Parameter

Tool ID 

Lock parameters 
 

Sleep Mode /
Sleep temperature

Hibernation delay

Minimum
temperature

Maximum
temperature

Tool status

Temperature units

Description

Allows to modify the tool identifier.

Allows to lock the parameters of the station using a four-digit code. The 
default code is 0105, but a new code can be set by simply entering some 
other four digits of choice when locking the parameters.

Set Sleep Mode on/off. The tip temperature will drop only to the selected 
Sleep temperature when placed on the tool holder.

Set Hibernation delay from 5 to 15 sec. The countdown starts when the 
tool remains inactive (no movement).

Select the minimum temperature that can be set for the Work Mode.

Select the maximum temperature that can be set for the Work Mode.

The different colors and light modes of the status indicator light mean the 
following:
- Green: working / soldering
- Green blinking: charging
- Alternating red/green blinking: low battery, less than 20%
- Red blinking: no cartridge
- Blue blinkin: safety cap on and tool disconnected from the station
- No color: power off

Allows to change the units of temperature measurement between Celsius 
degrees and Farenheit degrees.

Settings

20

Summary of Contents for B-IRON 210 DUAL





























Reviews: