ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
8/82
USB1.1 Mk2
If the menu option has submenus, use the JOG-WHEEL (9) to browse these.
Press the TRACK knob (16) again to return to the main menu.
To save your settings: choose menu option 7 (EXIT & SAVE) and press the TRACK knob (16)
1. SLEEP TIME:
to extend the lifetime of the laser, the unit goes automatically to sleep mode while not used
for 15 minutes (default). In this menu option you can change, the time it takes to enter sleep mode:
Turn the TRACK knob (16) to select the desired time: “No SLEEP”
120 minutes.
Press the TRACK knob (16) to save the new value and return to the main menu.
2. Line Setup:
you can configure how the text line shows information that is longer than 10 characters. You
can choose 3 different modes + some extra fine-tuning:
There are 3 submenus: turn the JOG-WHEEL (9) to select a submenu.
o
Submenu 1 - L1 Mode:
Turn the TRACK knob (16) to select the desired setting:
L1 Mode = 1:
text line scrolls and waits for a certain time before scrolling
starts again. You can set the waiting time in submenu2.
L1 Mode = 2:
text line scrolls only one time, then stops.
L1 Mode = 3:
text line scrolls continuously.
o
Submenu 2
– start/stop waiting time for scrolling:
Turn the TRACK knob (16) to select the desired value:
Dis. = 0.5s
12.0s:
waiting time in seconds.
o
Submenu 3
– scrolling speed:
Turn the TRACK knob (16) to select the desired value:
Run = 50
2000ms:
50ms = fast speed / 2000ms = slow speed
Press the TRACK knob (16) to save the new values and return to the main menu.
3. SGL/CONT:
You can choose bet
ween “single track mode” and “continuous play”.
Continuous play: the complete CD/USB-drive will be played without interruption. (used in pubs)
Single track: player stops at the end of each track and waits at the beginning of the next track.
(mostly used by deejays)
Turn the TRACK knob (16) to select the desired mode. Press the TRACK knob (16) to save the
new value and return to the main menu.
4. AUTOCUE MODE:
while switched on the player stops at the end of each track and waits at the first
music note of the next track. This means that badly indexed CDs will not interfere with the instant start
capabilities of the player, a very useful feature for deejays!
5. REC. USB:
you can select to which USB-slot (USB1 or USB2) the recording whould be sent.
6. REC. Bitrate:
you can choose the quality of your MP3-recording. Turn the TRACK knob (16) to select the
desired recording quality: quality goes from 32 kbps (lowest quality) up to 320 kbps (highest quality).
7. Firmware version / upgrading:
use this option to check and/or upgrade the firmware versions.
Turn the TRACK knob (16) to select the 2 firmware parts:
o
CON: xx:
shows the version of the control firmware
o
DSP: xx:
shows the version of the DSP firmware
o
Upgrade:
blinks when the unit is ready to check if there are new firmware versions
available. See “FIRMWARE UPGRADING” for more information.
Press the TRACK knob (16) to return to the main menu.
8. Load defaults:
If you really messed up things, you can still reload the default setting!
While “Load Defaults” is shown on the display: press the TRACK knob (16) to load the defaults.
9. Exit & Save:
if you want your changes to the setup menu to be permanently saved (also after switching
the unit off) you MUST use this option!
Press the TRACK knob (16) : the display shows “Saving” and exits the setup menu.
FIRMWARE UPGRADING
We strongly suggest to regularly check the USB1.1 Mk2 product page on
www.jbsystems.be
to see if new
firmware updates are available. Upgrading firmware should always be done very carefully!
Download the file containing the upgrade file(s)
Read the instructions and follow them strictly, otherwise you could damage your equipment…
Put the files on an EMPTY
(important!)
USB-stick.
Press the TIME button (26) for about 3seconds to enter the setup menu.
Use the TRACK knob (16) t
o browse to menu option “
5. Version
”.
