background image

 

 

12 

 

PRODUCT WARRANTY

 

For 5 years from the date of installation, this product will be repaired, or replaced free of charge, if 

defective in material or workmanship.   

 

ADDITIONAL    WARRANTY ON PARTS 

Replacement parts for any defective parts on this product will be furnished, free of charge. Any costs for 

professional installation are included. 

 

WARRANTY RESTRICTION 

This Garage Door Opener    Warranty does not cover light bulbs or fuses, which are expendable parts, or 

repair parts necessary because of operator abuse or negligence, including the failure to adjust and 

operate this garage door opener according to instructions contained in the owners manual. This   

warranty also does not cover any problems caused by interference or impact damage and does not cover 

remote controls. 

This warranty remains valid providing the door has been serviced at least every 2 years by any 

professional garage door company since the installation of this opener. Proof of    service will be 

requested and failure to produce this may void your warranty. 

Warranty is void if damage or premature wear to the opener is sustained by a broken, unbalanced, worn 

or damaged garage door.   

Original purchase receipt / Invoice is required to process a warranty claim.   

If a technician is requested to attend and rectify the issue and it is reasonably deemed to be caused by 

other factors other than a product fault the customer agrees that they may be charged a call out fee, plus 

any parts required to complete the repair. 

 

Liability 

 Australia only

 

Under no circumstances shall the Seller be liable for consequential, incidental or special damages arising 

in 

connection with the use, or inability to use, the Unit. In no event shall the Seller's liability for damages or 

injury arising from breach of law or contract or for negligence, exceed the cost of repairing or replacing the 

Unit or refunding the purchase price of the Unit. Under Division 2 Part V of the Trade Practices Act, 1974, 

certain warranties and conditions (Implied Terms) are implied into contracts for the supply of goods or 

services if the goods or services are of a kind ordinarily acquired for personal, domestic or household use 

or consumption. Liability for breach of those Implied Terms cannot be excluded or limited and the 

limitations and exclusions above do not apply to the Implied Terms. Except for the Implied Terms and the 

warranties set out above, the Seller excludes all warranties and conditions implied by statute, at law, in 

fact or otherwise. 

 

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are 

entitled to a replacement or refund for a major failure and compensation for any other reasonably 

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail 

to be of acceptable quality and the failure does not amount to a major failure.

   

If you believe you have a faulty product you may submit a warranty request by contacting the company 

listed below. 

Summary of Contents for 1200 V1














Reviews: