background image

 

- 1 - 

Important safety recommendations 

 
FAILURE 

TO 

COMPLY 

WITH 

THE 

FOLLOWING 

SAFETY 

RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, 
DEATH  AND  /  OR  PROPERTY  DAMAGE.  WE  STRONGLY 
RECOMMEND  INSTALLATION  IS  COMPLETED  BY  A  TRAINED 
TECHNICIAN.   

PLEASE  READ  CAREFULLY  AND  ADHERE  TO  ALL  SAFETY  AND 
INSTALLATION RECOMMENDATIONS. 

This  opener  is  designed  and  manufactured  to  meet  Australian 
Standards AS/NZS 60335.2.95:2012  and AS/NZS  60335.1:2011 
when installed correctly.

 

Unqualified  personnel  or  those  persons,  who  do  not  know  the     
occupational  health  and  safety  standards  being  applicable  to 
automatic  garage  doors,  must  in  no  circumstances  carry  out 
installations or implement systems.

 

Persons  who  install  or  service  this  equipment  without  observing 
all  the  applicable  safety  standards  will  be  responsible  for  any 
damage,  injury,  expense  or  claim  as  a  result  of  failure  to  install 
the  system  correctly  and  in  accordance  with  the  relevant  safety 
standards. 
For  additional  safety  we  recommend  the  inclusion  of  a  Photo 
Beam  System.  Although  the  opener  incorporates  a  pressure 
sensitive  Safety  Obstruction  Force  system,  the  addition  of  a 
Photo Beam System will greatly enhance the operating safety of 
an automatic garage door.

 

Make sure that the garage door is fully open & stationary before 
driving in or out of the garage.

 

Make  sure  the  garage  door  is  fully  closed  &  stationary  after 
operation.

 

Keep hands and loose clothing away from the opener and garage 
door during operation.

 

The  Safety  Obstruction  Force  System  is  designed  to  work  on 
STATIONARY objects only. Serious personal injury, death and / or 
property damage may occur if the garage door contacts a moving 
object.

 

Summary of Contents for 1000N




















Reviews: