![background image](http://html1.mh-extra.com/html/jayco/recon-zx-2008/recon-zx-2008_owners-manual_3681398076.webp)
SECTION 11
CAMPING & OPERATING
72
5. Push down on the top of the back rest and
the front edge of the seat to lay it into the
bed position.
6. To store the couch/dinette against the
wall, it is necessary to have it in the bed
position.
Fig. 11.2 Couch/J-steel dinette
To complete the dinette set up, position the
table between the dinette seats.
J-Steel dinette and couch removal
The J-steel dinette
and couch are
designed for removal
from the wall to
create more room in
the cargo area.
Loosen the thumb
bolt securing the
bracket to the trailer wall.
1. Lift up on the J-steel frame to remove it
from the bracket.
2. Store and secure the J-steel dinette/couch
in an appropriate place while traveling.
3. To set up, return the J-steel frame to the
appropriate bracket.
4. Tighten the thumb bolt to secure the
dinette/couch in place.
The thumb bolt securing the J-steel
dinette/couch frames must always be
tightened when to prevent the J-steel from
detaching from the bracket and damaging
the trailer.
R
EAR
B
ED
(I
F
S
O
E
QUIPPED
)
Power operation (if so equipped)
The electric bed lift operates on 12-volt DC
power supplied by the tow vehicle charge line,
auxiliary batteries, or power converter. The
RV should be hooked up to 120-volt AC
power and have the power converter
operating, if possible.
There are two separate switches used to
operate the bed lift: a backlit master shutoff
switch located near the entry door and a bed
lift “Up/Down” switch located elsewhere in the
trailer.
The master switch must be in the “ON”
position for the “Up/Down” switch to be
operational.
To lower the bed lift, press the “DOWN”
section of the “Up/Down” switch. Lower
the bed to the desired position or until it
automatically stops at its lower limit.
To store the bed, remove any obstacles
laying on the bunk. Press the “UP” section of
the “Up/Down” switch. Raise the bed to the
desired position or until it automatically stops
at its upper limit.
DO NOT LOAD MORE THAN 600# ON
THE BED.
Damage to the bed lift
mechanism and personal injury may result
from overloading.
RAISE THE REAR BED TO THE
HIGHEST POSITION WHEN TOWING
YOUR RV
. Damage to the rear bed may
result from traveling with the bed in
lowered positions.
Fig. 11.3 Thumb bolt
Summary of Contents for Recon ZX 2008
