![background image](http://html1.mh-extra.com/html/jayco/recon-zx-2008/recon-zx-2008_owners-manual_3681398069.webp)
SECTION 10
SLIDEOUT SYTEMS
65
The slideout room system is designed for
additional floor space and comfort. The
mechanical components are gear driven.
Electric powered slideout room systems have
a manual override to allow you to extend or
retract the slideout room(s) in case of a power
loss. Make sure you have sufficient power
available before operating your slideout
system.
O
PERATING
T
HE
S
LIDEOUT
1.
The auxiliary batteries (customer
supplied) must be fully charged and
connected. If possible, the RV should be
hooked up to 120-volt AC power so that
the converter operates.
2. The RV must be level and the stabilizer
jacks in the extended position.
3. Locate the slideout room
control switch. The main
slideout switch (if so
equipped) is located in the
command center. The
bedroom slideout switch
(if so equipped) is located
on an bedroom interior
wall.
4. To move the room out,
press the OUT section of
the switch and hold it until
the motor stops (travel
time is approx. 25 seconds). Operating
the switch after the room is fully extended
will damage the switch and motor.
After the slideout is
extended, verify that
the corners of the
black rubber seal are
set up correctly. The
corners of this seal
are cut at a 45°
angle. The top of the
seal must overlap
the side of the seal
to avoid the
possibility of water
penetration.
Retracting slideout room
Press the IN section of the slideout room
control switch and hold it until the motor
stops. Operating the switch after the room is
fully retracted will damage the switch and
motor.
Additional support jacks are not needed
under the slideout. Damage can occur to
your slideout room from improper use of
aftermarket support jacks.
Ensure that the trailer is level before
operating the slideout room. Water leaks
and other problems could result if the
slideout is operated without leveling the
trailer.
Ensure there are no people or obstructions
blocking the path of the room when it is
moving. Keep away from the slide rails
when the room is in motion. The gear
assembly may pinch or catch on loose
clothing causing personal injury.
Ensure the slideout is in the closed
position prior to hooking the unit to the tow
vehicle.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
Do not place excessive weight in the
slideout room. It can cause the slideout
room to malfunction and cause damage to
the slideout.
Fig. 10.1
Bedroom
slideout
control
switch
Fig. 10.2 Exterior
slideout room
corner
Summary of Contents for Recon ZX 2008
