![background image](http://html1.mh-extra.com/html/jayco/2012-jay-feather-ultralite/2012-jay-feather-ultralite_owners-manual_3475199068.webp)
SECTION 8
TENT CARE TOWABLE – EXPANDABLE MODELS
3. From the interior, place the C-shaped end of
the bed bow brace onto the bed bow
connector (Fig. A). Push the bed bow brace
outward and upward while pressing the
second button from the curved end of the
bed bow brace. Insert the end of the brace
into the bracket mounted on the shelf, just
past the first button (Fig. B). Release the
button.
Attach the hinge cover to the bed board by
placing the Velcro strip on the hinge cover
ed mat and slide on to the
4.
onto the Velcro strip on the bed board and
pressing firmly.
5. Push the bed mats onto the bed board.
Unfold the hing
bed platform. Fold the canvas straps under
the front edge of the small bed mat.
Condensation can be prevalent if proper
ventilation is not used. It can exist whether or
side and rear bed bow
move the bunk mat from the front bed
, set aside. Make sure all loose
. Lay the cover back on
hing in on the exposed
orm. Fold
.
d in
at least 1” above the side bulb seal.
. Lift the bed up and hold it in a vertical
position. Tuck the tent in on both sides.
e perimeter
re is nothing
not a heater is used. We recommend that you
leave a small opening in each bunk zipper to
permit air to flow through and allow the tent to
“breathe.” This will help minimize moisture
gathering above the bunk area on the vinyl (see
Condensation).
Closing the beds
NOTE: The front bed mat will be the easiest
place to store the
Ma
braces. Starting with the front bed will enable
you to take the bed bow braces off of the rear
and side and immediately store them. Caution
should be taken to place the bed bow braces in
the mat with the curved part down to prevent
the bed bow brace ends from damaging the
mat.
Front bed
1. Re
platform
items have been removed from the bunk
mat and bed platform. Items left in
these areas may cause damage to the
mats and tent.
2. Loosen the hinge cover by lifting up on
the Velcro side
the bed shelf.
3. Remove the bed bow brace from the
ceiling by pus
button and pulling down. Pull the bed
bow towards you and remove the C-
shaped connector from the bed bow.
Set the bed bow brace aside.
4. From the exterior, lift the bottom of the
tent up exposing the bed platf
8.2 Fig. A 8.2 Fig. B
the tent in towards the center of the bed
platform.
5
Make sure the bed tent is pushe
6
ke sure the top of the door is clear
from obstructions.
7. Latch one side of the door.
8. From the interior, inspect th
of the door making sure the
obstructing the top and sides of the
door. Make sure the hinge cover is
clear of the door.
8 - 2
Summary of Contents for 2012 Jay Feather Ultralite
