Jaycar NIP-09L2J User Manual Download Page 4

Page: 4 / 42

IP Camera User Guide

Page 4

Network Camera Installation Manual

Tips: If necessary, reset the camera; please find the "RESET" button at the bottom of the device

or in the tail of device , hold 10 seconds to reset while it is power connected!

1. Hardware installation

1.1 Hardware connection

Connect the power supply and network cable,Check if the power indicator (green) and the network

indicator (yellow) is working properly. If it is ok,then Pan and tilt will rotating automatically

。

Note: picture is for reference only,To prevail in kind

！

Power indicator: indicator is on while power on.

I/O port

：

connect with PIR /alarm etc.

Network indicator:Flashes when transferring data

Power supply: 5V

RJ45: connect with router

SD slot:for TF/SD card

WIFI antenna: Receiving a wireless signal

Audio output:connect with speaker.

I/O port

SD slot

Audio out

Power connector

WIFI antenna

RJ45

Network indicator

Power indicator

Summary of Contents for NIP-09L2J











































Search results

Summary of Contents for NIP-09L2J

Reviews:

Related manuals for NIP-09L2J

Brands by name

Popular brands

Jaycar NIP-09L2J, User Manual

Search results

Summary of Contents for NIP-09L2J

Reviews:

Related manuals for NIP-09L2J

Brands by name

Popular brands