Jason International, Inc. •
501.771.4477
Page 10 of 16
Customer Service : 800.255.5766
Copyright © 2014 Jason International.
Home spa toUCHpad
All functions of the Jason Home Spa bath can be conveniently
operated with either one of the two Home Spa digital keypad
controls which control the operation of the two whirlpool
pumps, the air blower, underwater mood lights, and the jetted
neck pillows. The dual keypads are used to run individual
pumps and jetted neck pillows. The same blower and lights
are controlled from both keypads.
Whirlpool on/off icon
To control the operation of the whirlpool pump motor, press
and release for each setting: On or Off. A 20 minute decreasing
timer will be initiated when the pump motor starts. Press and
hold the Pump icon to cycle through each pump setting. The
Pump icon lights when the water is at operating level and the
LCD displays “System Ready”. The LCD will display “WP Off”
or “WP On” when the key is pressed. It also toggles between
Temperature and Timer at 5 second intervals. “Low Water”
is displayed for 5 seconds if no water is detected.
Jetted neck pillow icon
To control the operation of the jetted neck pillow, press and
release for each setting, you can set for a constant flow on
both jets, a pulsing flow on both jets, or a pulsing alternating
flow between jets. Press and hold the Pillow icon to cycle
through the various pillow settings. The Pillow icon will light
whenever the pump is running. The solenoids will open for
two (2) minutes to drain during the purge cycle countdown.
The LCD will display “Pillow On”, “Pillow Pulse1”, “Pillow
Pulse2”, or “Pillow Off” while the key is pressed.
Airmasseur® on/off and mode icon
To control the operation of the blower, simply press and
release to change the setting to Constant, Wave, Pulse or
Off. A 20 minute decreasing timer will be initiated when the
blower motor starts. Press and hold the Blower icon to cycle
through blower modes. The Blower icon should remain lit as
long as the bath is connected to a power supply. The LCD
will display “Const Air” and blower speed, “Wave Air” and
blower speed, or “Pulse Air” and blower speed, while the
key is pressed. The time remaining on the purge cycle is
displayed after the bath has drained. “Purge Stop” is displayed
while the key is pressed during the purge cycle. This action
will terminate the purge cycle. The mode settings will be
remembered on the next startup.
blower Speeds icon
Hold the key in Constant mode to go from High to Low then
release and hold again to go from Low to High. Hold the
key in Wave and Pulse mode to go from High to Medium
and Medium to High. The system remembers the last speed
setting on the next startup. The Blower Speeds icon will light
up when the blower is running. The LED displays the blower
speed from “10” (Low) or “55”(Med) to “99” (High) while the
key is pressed. You can reduce the auto purge idle time
from 20 minutes to 10 minutes, by pressing and holding the
key for more than 5-seconds during the purge idle period.
leD light icon
Hold the key for less than two (2) seconds to turn the lights
Off or On. Hold the key for more than two (2) seconds to
change modes. The Light icon should remain lit as long as
the bath is connected to a power supply. This function has
a two-hour timer and remembers the last mode. The LCD
displays “Light On” or “Light Off while the key is pressed
for less than two (2) seconds, “Light Cycle” is displayed if
pressed for more than two (2) seconds.
P
AirMasseur
®
On/Off, Mode
Blower Speeds
LED Light
IR for Remote
Whirlpool On/Off
Pillow On/Off
opeRating instRUCtions, featURes, and ContRols (cont.)
Figure 5