background image

Jason International, Inc.  •  

 

501.771.4477  

    

Page 3 of 17

    

Customer Service :  800.255.5766 

Copyright © 2013 Jason International.

INSTALLATION INSTRUCTIONS (cont.)

10.  

Protect the acrylic bath surface from damage  

during installation with a suitable material, i.e., 

cardboard and/or plastic film.

 The acrylic surface 

of this bath has been provided with a protective film 
which helps protect the bath during shipment and 
installation. Additional protection may also be required 
to protect the acrylic surface during installation. If the 
bath is tiled in, remove the necessary portion of the 
film when installing the tile.

FIeLD INSTALLATION  

OF THe MICROSILK

®

 PUMP ASSeMBLY

The Jason MicroSilk

®

 system has been factory assembled 

following ETL and IAPMO guidelines. For shipping  
purposes, on some bath models, the MicroSilk

®

 Pump 

Assembly may be packaged separately and disconnected 
from the bath. 

NOTe: These instructions can also be found in the 

Installation, Operation and Maintenance manual of the 

separately packaged MicroSilk

®

 hydrotherapy bath 

unit. 

WARNING:  SYSTeM UNDeR PReSSURe – NeVeR  

PeRFORM MAINTeNANCe WHILe SYSTeM IS RUNNING.

Figure  3

Figure  4

Note:

 Verify the MicroSilk

®

 Pump Assembly is the same 

unit that was provided for the bath being installed. The  
serial number listed on the label provided on the MicroSilk

®

 

Pump Assembly carton should match the serial number of 
the bath.

Warning: Any modification to the equipment is not  

recommended and will VOID the manufacturer’s  

warranty.

To install the MicroSilk

®

 Pump Assembly to the bath, the 

following procedures must be followed.

Note:

 Do not install the MicroSilk

®

 Pump Assembly further 

than the length of the tubing that is factory installed on the 
bath. These tubing lengths have been designed for proper 
drainage of the system.

1.  Position the bath in the area of intended installation.

2.  Before beginning any work, the installer is to determine 

the proper location of the MicroSilk

®

 Pump Assembly 

and service access.

3.  Do not disconnect the plumbing lines that are secured 

to the bath with nylon tie straps 

(Figure 5)

.

Figure  5

Summary of Contents for Forma MicroSilk-AirMasseur


















Reviews: