specifications, installation
and operation instructions
page 8 of 16
Model SEC 180--2, 230--2 and 280--2
JARVIS
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA E--MAIL. [email protected]
TEL. 860-347-7271 FAX. 860-347-6978 www.jarvisproducts.com
6204015::
®
SPECIFICATIONS
SEC 180--2
Motor Power
1.9 hp
1400 W
Operating Voltages 230 / 115 V, 1 phase, 50 / 60 Hz
Full Load Amps
6.5A @ 230V
13A @ 115V
Blade Speed
1650 rpm
Control Handles
Single Trigger / Dual Handles
Electric
Brake
Mechanical
Blade Diameter
7.1 in
180 mm
Cutting Depth
2.6 in
66 mm
Overall Length
21.5 in
546 mm
Weight
14.6 lbs
6.6 kg
Vibration
less than (<) 126 dB
< 2 m/sec
2
Noise (one meter from tool)
< 85 dBa
SEC 230--2 / SEC 280--2
Motor Power
2.4 hp
1800 W
Operating Voltages 230 / 115 V, 1 phase, 50 / 60 Hz
Full Load Amps
8.4A @ 230V
16.8A @ 115V
Blade Speed
1300 rpm
Control Handles
Single Trigger / Dual Handles
Electric
Brake
Mechanical
Blade Diameter
SEC 230--2
9.1 in
230 mm
SEC 280--2
11.0 in
280 mm
Cutting Depth
SEC 230--2
3.0 in
76 mm
SEC 280--2
4.0 in
102 mm
Overall Length
SEC 230--2
22.5 in
572 mm
SEC 280--2
30 in
762 mm
Weight
SEC 230--2
22 lbs
10 kg
SEC 280--2
24 lbs
11 kg
Vibration
less than (<) 123 dB
< 1.3 m/sec
2
Noise
<85 dBa
INSTALLATION INSTRUCTIONS
ALWAYS DISCONNECT THE POWER SUPPLY IN ACCOR-
DANCE WITH OSHA’S LOCKOUT/TAGOUT PROCEDURES
(29 CFR 1910.147) BEFORE PERFORMING ANY REPAIRS OR
MAINTENANCE. ALL WIRING MUST BE DONE IN ACCOR-
DANCE WITH NATIONAL, STATE AND LOCAL ELECTRICAL
CODES.
Refer to Figures A to D on pages 4 through 7 for refer-
enced items.
1 Install a balancer above the work station on a trolley.
1.1 The trolley should have sufficient travel to allow
the operator to reach the entire work area.
2 Suspend the tool from the balancer.
2.1 Adjust the balancer to the operator’s preference.
3 Install plug of your choice to end of electrical cord
(item 138).
4 Plug the tool into appropriate power supply outlet.
OPERATION INSTRUCTIONS
1 Plug in the tool.
2
Each day
before you begin operation, perform the
following:
2.1 Make sure that tool moves freely on its balancer.
2.2 Make sure that the saw is working correctly.
Depress
the trigger and the tool should start.
Release
the trigger and the tool should stop
within 3 seconds.
If the tool malfunctions, re-
move it from service and report the problem to
your supervisor immediately
.
Always use two hands when starting and stopping the
tool. Continue holding the tool with two hands until the
saw blade comes to a complete stop.
3 Make the cut:
3.1 Position the saw.
3.2
Depress
the trigger and make the cut.
3.3 When the desired length of cut is reached, re-
lease the trigger. This will stop the blade from
rotating.
3.4 Withdraw the saw from the carcass.
4 Unplug the tool.
