background image

safety messages to employer

and safety director

page 2 of 16

Model SEC 180--2, 230--2 and 280--2

JARVIS

PRODUCTS CORPORATION

33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA E--MAIL. [email protected]
TEL. 860-347-7271 FAX. 860-347-6978 www.jarvisproducts.com

6204015::

®

1. Ensure

that all employees who use this tool are trained in the proper use of this tool and are aware of

the dangers that may arise if they do not follow procedures outlined in this brochure.

2. Enclosed

are four (4) copies of

“NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP

PERSONNEL”.

Post one copy on the employees’ bulletin board; give one copy to the operator(s);

give one copy to the maintenance foreman; and give one copy to the sub-contract cleanup / internal
cleanup foreman.

Additional copies will be provided upon request.

3.

The tool is designed and intended to be powerful. This fact should be obvious to your employees, but
you must emphasize it to them.

4. Ensure

that all employees are instructed not to walk in front of the tool during its use.

5. Ensure

that eye protection is worn in accordance with OSHA’s eye and face protection requirements

(29 CFR 1910.147) when operating the tool.

6. Ensure

that proper procedures are established in accordance with OSHA’s lockout/tagout procedures

(29 CFR 1910.147) to prevent accidental startup or release of stored energy.

7. Follow

our installation and maintenance instructions for proper installation and care of the tool.

8. Never

make modifications or alterations to the tool.

Replace any missing or illegible labels.

9. Remove

and

repair

any tool that malfunctions. All personnel must be instructed to remove any

malfunctioning equipment.

10. Avoid

injury. Do not permit the tool to be misused.

11. If

you

resell

or

distribute

a Jarvis product, you must provide the purchaser with the appropriate safety

sheets and tool brochure.

Additional copies of safety sheets and tool brochures will be provided upon

request.

SAFETY MESSAGES TO EMPLOYER AND SAFETY DIRECTOR

AVOID INJURY

Keep hands clear.

Summary of Contents for SEC 180-2

















Reviews: