background image

 

 
 
 
 

 

CLEARANCES 

 
 

Floor         
                  

Trident and Laguna :             12''  (304.8mm) 

Fogo, Vesuve and Kilauea :       Combustible 

Lateral wall (left or right) (See  P.7 Fig. 2) 

12''   (304.8 mm) 

Opposite wall (See  P.8 Fig. 4) 

36''   (914.4 mm) 

Rear wall 
Air circulation (See P.9 Fig.6) 

0''   (0 mm) 

1''   (25.4 mm) 

Appliance Front 

24''   (609.6 mm) 

Top of burner (See  P.7-8 Fig. 2, 3, 4 ,5) 

40''   (1016 mm) 

*ALWAYS  USE  J.A.  ROBY  ETHANOL  WITH  YOUR  APPLIANCE  OR  YOUR 
WARRANTY WILL BE CANCELED. 

 

FIREPLACE LOCATION 

   

You have just acquired an 

unvented decorative fireplace

. The location of your J.A. Roby 

Inc. appliance is the key to an efficient, safe and easy use of your new appliance.

 

 
Your  decorative  fireplace  must  be  installed  in  a  well  aerated  and  easy  access  place  to 

enable ignition, filling and extinction of the burner 

 

The fireplace must be installed on a solid wall  

 

For your safety, make sure to use the screws included in package to secure the fireplace onto 
the wall which will provide stability to your fireplace.

 

 

It is mandatory to follow the clearances for the installation of the fireplace. 
 
 

WARNING 

Before installing, please take a few minutes to read this handbook carefully and also read the 

warning notice on the ethanol fireplace (yellow  and orange).  Keep it in  a secure and  easily 

reachable place for future references. If this appliance is not properly installed, it could cause 

fire damages to the property, injuries or death. 

 

Summary of Contents for Volcan B12 FOGO


























Reviews: