background image

15

Mechanical adjustment

Setscrew C

Setscrew B

Setscrew A

Hook base plate

Adjustment 1

1.  Remove the bed cover (see page 3).

2.  Turn the power switch ON, and select the zigzag stitch  
  pattern 11.
  Adjust the stitch width at its maximum (9.0).

3.  Remove the presser foot, needle plate and bobbin    
 holder.

4.  Loosen the setscrews A and B.
  Loosen the setscrew C just enough to move the hook  
  base plate.

5.  Turn the handwheel toward you.
  Adjust the clearance between the needle and the tip    
  of the rotary hook by moving the hook base plate up 
  or down between -0.1and +0.05 mm at the both left    
  and right needle position.

6.  Tighten the setscrews A, B and C.

7.  Check the backlash between the lower shaft gear and  
  the hook drive gear. If the backlash is too great or the 
  engagement of the gears is too tight, adjust the  

 

  backlash (see page 20).
  * Check the hook timing and needle bar height 
     after this adjustment (see page 17 and 18)

Clearance between needle and tip of the rotary hook

The clearance between the needle and the point of hook should be -0.1 to +0.05 mm.

Summary of Contents for Skyline S5







































Reviews: