Janome Magnolia 7325 Service Manual Download Page 2

Page: 2 / 22

SERVICE MANUAL

Service Access (1) Face plate .....................................................................................1

Service Access (2) Base cover ...................................................................................2

Service Access (3) Front cover ...................................................................................3

Service Access (4) Rear cover ....................................................................................4

Adjusting Thread Tension ............................................................................................5

Adjusting Presser Foot Height and Alignment .............................................................6

Adjusting Needle Swing ..............................................................................................7

Adjusting Needle Drop Position ...................................................................................8

Adjusting Hook Timing ................................................................................................9

Adjusting Needle Bar Height ......................................................................................10

Adjusting Clearance between Needle and Hook Point ...............................................11

Adjusting Backlash between Hook Drive Gear and Lower Shaft Gear .......................12

Adjusting Feed Dog Height ........................................................................................13

Adjusting Feed Balance .............................................................................................14

Adjusting Buttonhole Feed Balance ...........................................................................15

Adjusting Buttonhole Zero Feed .................................................................................16

Adjusting Buttonhole Function ...................................................................................17

Replacing Motor and Adjusting Motor Belt Tension ....................................................18

Replacing and Adjusting Threader .............................................................................19

Replacing Printed Circuit Board B and Fuse ..............................................................20

PARTS LIST

PARTS LIST ........................................................................................................... 21~43

TABLE OF CONTENTS

Summary of Contents for Magnolia 7325























Search results

Summary of Contents for Magnolia 7325

Reviews:

Related manuals for Magnolia 7325

Brands by name

Popular brands

Janome Magnolia 7325, Service Manual

Search results

Summary of Contents for Magnolia 7325

Reviews:

Related manuals for Magnolia 7325

Brands by name

Popular brands