Janome HF106 Instructions For Use Manual Download Page 6

2  - 5

1 - 5

A

B

1

2

3

4

5

 6

7

19. Tricot Stitch

Thread tension dial

Machine setting

Place the fabric under the presser foot so that the edge is
just inside the right side of the presser foot.
Guide the fabric so the right hand stitches fall at the edge
of the fabric.

20. Buttonhole

Machine setting

Stitch

Thread tension dial

Buttonhole foot

Make a test buttonhole  using the same fabric and interfacing as the actual garment.

Procedure

1  Raise the needle and turn the pattern
    selector dial to select     .
    Draw the both threads to the left.
    Lower the needle down into the fabric
    at the starting point A, and lower the
    buttonhole foot.
2  Sew down the left side stopping at the
    bottommark B.
3  Raise the needle and select     .
    Sew 5 stitches of bartack and stop the
    machine.
4  Raise the needle and select     .
    Sew up the right side of the
    buttonhole, stop the machine when
    you are directly opposite the first stitch
    on the left hand side.

5  Raise the needle and select     .
    Sew 5 stitches of bartack and raise the
    needle out from the fabric.
6  Raise the presser foot, remove the fabric
    from the machine and cut the threads
    leaving 4” (10 cm) tails.
7  Insert a pin at the end of the buttonhole
    as shown, then cut the opening with a
    seam ripper.

Note:

 Make sure not to cut the stitches.

Changing the
presser foot

Loosen the screw and
replace the presser
foot.
Tighten the screw.

Corded Buttonhole

With the buttonhole foot raised, hook a fillar cord on
the spur on the back of the foot.
Bring the ends toward you under the foot until they
clear the front end.

Hook both ends into the forks on the front of the foot
to hold them tight.

Lower the needle down into the fabric at the starting
point, and lower the presser foot.

Sew a buttonhole over the fillar cord.
Pull the left end of the cord to tighten it and cut.

Seam ripper

Bobbin thread

Needle
thread

Starting point A

Forks

Spur

Fillar code

Stitch

Pin

Summary of Contents for HF106









Reviews: