Janome FOUR-DBL Service Manual Download Page 29 | Manualshive

Page: 29 / 29

background image

27

TO ADJUST THE THREAD TENSION DIALS

To check:
Thread tension dials are already adjusted for general sewing at factory, however, if you want to adjust
much stronger or weaker special sewing, it can be adjusted as follow:

Adjustment procedure:
1.  Remove the back cover and the top cover.
2.  Adjust each thread tension with the adjusting plate A.
* If the thread tension is at stronger level, shift the adjusting plate in the direction B.
* If the thread tension is at weaker level, shift the adjusting plate in the direction C.
3.  Rotate the thread tension dial while sewing to check the sewing performance.
4.  Attach the top cover and the back cover.

Adjusting plate A

B

C

Top cover

Front cover unit

«
...
27
28
29

Summary of Contents for FOUR-DBL






























Reviews:

No comments

Related manuals for FOUR-DBL

Brand: Fellowes Pages: 9

Brand: Fellowes Pages: 5

Brand: Fellowes Pages: 6

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 76

Brand: Fellowes Pages: 6

Brand: Fellowes Pages: 8

Brand: Fellowes Pages: 74

Brand: Singer Pages: 12

Brand: Singer Pages: 41

Scholastic 85SCH

Brand: Singer Pages: 230

Brand: Ricoh Pages: 147

Brand: Stihl Pages: 132

Brand: Reliable Pages: 1

Code-a-phone 700

Brand: Ford Pages: 52

Brand: Kärcher Pages: 15

Brand: Janome Pages: 34

Brand: JUKI Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands