background image

18

to enteR self-diagnostiC mode:

PRePaRation:
 

1. tUrn the power Switch off.

 

2. move the bobbin winder Spindle to the left.

 

3. raiSe the feed dog.

 

4. Set the Speed control lever to the left.

 

5. remove the preSSer foot and raiSe the preSSer foot lifter.

 

6. tUrn the hand wheel toward yoU to raiSe the needle to itS higheSt poSition.

notes:

 

• Be careful: the sewIng machIne may start runnIng In Its own whIle In test mode.

 

• turn off the power swItch Before replacIng any parts.

 

• repeat the dIagnostIc test untIl the proBlem has Been resolved.

 

• you can skIp steps In the dIagnostIc procedure and go dIrectly to the test you  

 

want to perform.

 

(enter Self-diagnoStic mode, then Select the Step nUmber of the diagnoStic teSt  

 

yoU reqUire by preSSing the Start/Stop bUtton)

to begin:
 

tUrn on the Switch. if any of the following problemS occUr, take the 

 

recommended actionS in the order they are Shown.

     
1. the machine doeS not reSpond when the power Switch iS tUrned on:

   • check each connector connectIon
   • replace the machIne socket
   • replace the swItchIng regulator
   • replace the a-Board

2. the Sewing machine lamp doeS not light Up:

   • replace the lIght BulB
   • replace the a-Board

self-diagnostiC test

tUrn the power Switch 
on while SimUltaneoUSly 
preSSing needle Up/down 
bUtton and the locking 
Stitch bUtton.

the lcd diSplay will 
indicate “01”.

preSS the Start/Stop 
bUtton to enter the Self-
diagnoStic mode.

Summary of Contents for DC1050






























Reviews: