7 / 12
2
3
1
Dok Nr
. 2.040.120.1.a
Power Analyser
UMG 96 RM-E
Installation manual
Residual current monitoring (RCM)
Installation
Device settings
Power Analyser
17
18
5
6
8
7
4
The UMG 96 RM-E is a multi-functional net-
work analyser, which
• measures and monitors residual currents
(RCM) and currents at the central grounding
point (CGP). The residual current monitoring
is carried out via an external residual current
transformer (30 mA rated current) on the
current measurement inputs I5 and I6.
• measures and calculates electrical variables
such as voltage, current, power, energy,
harmonics, etc. in building installations,
on distribution units, circuit breakers and
busbar trunking systems.
• displays and saves measurement results
and transmits them via interfaces.
Install the UMG 96 RM-E in the weather-protected
front panel of switch cabinets.
Cut-out size:
92
+0.8
x 92
+0.8
mm
Ensure!
Adequate ventilation
• The device is installed
vertically!
• Observance of clearance to
adjacent components!
The UMG 96 RM-E
• is only approved for measuring current with
a current transformer.
• is intended for the connection of current
transformers with secondary currents of
../1 A and ../5 A.
• has the current transformer ratio set to 5/5 A
as standard.
L2
L3
N
L1
Load
9
19
15
16
10
13
14
11
12
L2 L3
N
L1
*1
*1
L2 L3
N L1
Last
PE
I5
I6
Deutsche V
ersion:
siehe V
or
derseite
User manual:
www
.janitza.com
Janitza electronics GmbH
Vor dem Polstück 6
D-35633 Lahnau / Germany
Support tel. +49 6441 9642-22
Fax +49 6441 9642-30
e-mail: [email protected]
Website: http://www.janitza.com
Disclaimer
The observance of the information products for
the devices is a prerequisite for safe operation
and to achieve the stipulated performance
characteristics and product characteristics.
Janitza electronics GmbH accepts no liability
for injuries to personnel, property damage
or financial losses arising due to a failure to
comply with the information products. Ensure
that your information products are accessible
and legible.
Further information can be found on our web-
site www.janitza.com at Support > Downloads.
Copyright notice
© 2016 - Janitza electronics GmbH - Lahnau.
All rights reserved. Duplication, editing,
distribution and any form of exploitation, also
as excerpts, is prohibited.
Subject to technical amendments
• Make sure that your device agrees with the
installation manual.
• Read and understand first product-related
documents.
• Keep product supporting documentation
throughout the life available and, where ap-
propriate, to pass on to subsequent users.
• Please inform yourself about device revisi-
ons and the associated adjustments to the
product-related documentation on
www.janitza.com.
Disposal
Please observe national regulations!
If disposing of individual parts, please dispose
of them in accordance with their nature and
existing country-specific regulations, for
example as:
• Electrical scrap
• Plastics
• Metals
Or, task a certified disposal business with the
scrapping.
Relevant laws, applied standards and
directives
The laws, standards and directives for the
device applied by Janitza electronic GmbH
can be found in the declaration of conformity
on our website.
General
Safety
Safety information
The installation manual does not represent a full
listing of all necessary safety measures required
for safe operation of the device.
Certain operating conditions may require further
measures. The installation manual contains
information that you must observe for your
own personal safety and to avoid damage to
property.
Symbols used:
c
This symbol is used as an addition
to the safety instructions and
warns of an electrical hazard.
m
This symbol is used as an addition
to the safety instructions and
warns of a potential hazard.
C
This symbol with the word
NOTE!
describes:
• Procedures that do not entail
any danger of injury.
• Important information,
procedures or handling steps.
Safety instructions are highlighted with
a warning triangle and shown as follows,
depending on the degree of hazard:
m
DANGER!
Indicates an immediately
threatening hazard that leads to
serious or even fatal injuries.
m
WARNING!
Indicates a potentially hazardous
situation that could lead to
serious or even fatal injuries.
m
CAUTION!
Indicates a potentially hazardous
situation that could lead to minor
injuries or damage to property.
Measures for safety
When operating electrical devices certain parts
of these devices inevitable carry dangerous
voltages. This could result in serious bodily
injury or damage to property if not handled
properly:
• Before establishing electrical connections
to the device, earth it at the ground wire
connection if there is one.
• Hazardous voltages may arise in all circuit
parts that are connected to the power supply.
• Even after disconnecting the supply voltage,
there may still be hazardous voltages
present in the device (capacitor storage).
• Do not operate equipment with current
transformer circuits when open.
• Do not exceed the limit values stipulated in
the user manual and on the rating plate - even
during testing or commissioning.
• Observe the safety and warning information in
the documents that belong to the devices!
Qualified personnel
In order to avoid injuries to personnel and
property damage, only qualified personnel with
electrical training are permitted to work on the
devices with knowledge
• of the national regulations for accident
prevention
• of safety standards
• of installation, commissioning and operation
of the device.
Proper use
The device is
• intended for installation in switch cabinets
and small installation distributors (please
observe step 3 “Assembly”).
• not intended for installation in vehicles!
The use of the device in mobile equipment
is considered to be non-standard
environmental conditions and is therefore
only permitted after separate agreement.
• not intended for installation in environments
with hazardous oils, acids, gases, vapours,
dusts, radiation, etc.
The prerequisites of faultless, safe operation
of this device are proper transport and proper
storage, set-up, installation, operation and
maintenance.
C
NOTE!
If residual currents in electrical systems
are monitored, the device (inputs I5/I6)
can trigger warning pulses if a response
threshold is exceeded. The warning pulses
can provide an alarm before a protective
device trips.
The device does not provide protection
against electric shock!
m
CAUTION!
Damage to property due to
disregard of the installation
instructions
Disregard of the installation instructions can
damage or destroy your device.
Ensure that you have enough air circulation
in your installation environment and in the
event of high environmental temperatures,
provide cooling if necessary.
Brief description of device
Assembly
Connecting the supply voltage
The supply voltage level for your device is
specified on the rating plate.
After connecting the supply voltage, an indication
appears on the display. If no indication appears,
check whether the supply voltage is within the
rated voltage range.
N
L
Fig. Connection of supply voltage.
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Device inputs that are dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
m
CAUTION!
Damage to property due to
disregard of the connection
conditions or impermissible
overvoltage!
Your device can be damaged or destroyed
by a failure to comply with the connection
conditions or by exceeding the permissible
voltage range.
Before connecting the device to the supply
voltage, please check:
•
Voltage and frequency correspond to the
details on the ratings plate! Limit values
stipulated in the user manual have been
complied with!
•
In building installations, the supply
voltage must be protected with a UL/IEC
approved circuit breaker / a fuse!
•
The isolation device
-
must be installed near the device and
in a location that is easily accessible
for the user.
-
must be labelled to identify the
respective device.
•
Do not tap the supply voltage from the
voltage transformer.
•
Provide a fuse for the neutral conductor
if the neutral conductor terminal of the
source is not grounded.
Mains systems
Three-phase, four-conductor system
with earthed neutral conductor
Three-phase, four-conductor system
with non-earthed neutral conductor
(IT networks)
Three-phase, three-conductor systems
Non-earthed
Three-phase, three-conductor systems
With earthed phase
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-L
480 VLL
U
L-L
240 VLL
Single-phase, two-conductor systems
with earthed neutral conductor
Separated single-phase,
three-conductor systems
with earthed neutral conductor
The device can be used in
• 2, 3 and 4 conductor
networks (TN, TT and
IT networks)
• residential and
industrial applications.
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
230 VLN
U
L-N
/ U
L-L
240 VLN / 480 VLL
Voltage measurement
The device has 3 voltage measurement inputs
and is suitable for various connection variants,
with direct connection or via voltage transformer.
m
CAUTION!
Danger of injury or damage to
the device
Disregard of the connection conditions for the
voltage measurement inputs can result in injuries
or to the device being damaged.
For this reason, note that:
•
The voltage measurement inputs
-
are not connected to DC voltage.
-
are equipped with a suitable, labelled
fuse and isolation device located in
the vicinity (alternative: circuit breaker)
located nearby.
-
are dangerous to touch.
•
Voltages that exceed the allowed network
rated voltages must be connected via
a voltage transformer.
•
Measured voltages and measured currents
must derive from the same network!
L2
L3
N
L1
Connection variant
3p 4w
Voltage measurement
(Addr. 509 = 0, standard setting)
Fuse (UL/IEC listed)
Current measurement I1, I2, I3
Connection variants for voltage measurement
3p 4w
(Addr. 509 = 0, standard setting)
3p 4wu
(Addr. 509 = 1)
3p 4u
(Addr. 509 = 2)
3p 2u
(Addr. 509 = 5)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measurement with 3 phase
conductors and neutral conductor.
Measurement via voltage
transformer with 3 phase
conductors and neutral conductor.
Measurement with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
Measurement via voltage
transformer with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
1p 2w1
(Addr. 509 = 4)
2p 4w
(Addr. 509 = 3)
1p 2w
(Addr. 509 = 6)
3p 1w
(Addr. 509 = 7)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measured values derived from
voltage measurement inputs V2
and V3 are taken to be 0 and are
not calculated.
System with equal loading of the
phases. The measured values of
the voltage measurement input V2
are calculated.
TN-C system with 1-phase, three-
conductor connection. Measured
values derived from voltage
measurement input V3 are taken to
be 0 and are not calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Connection variant
3p 4w Current measurement
(I1, I2, I3) via current transformer
(Addr. 510 = 0,
standard setting).
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Current measurement inputs on the device
and on the current transformer that are
dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
Earth your system! Use the earth connection
points with earthing symbols for this!
Earth the secondary windings of current
transformers and all of the metal parts of the
transformer that could be touched!
C
NOTE!
If the measurement range is exceeded,
the measurement device display shows
"EEE"
. Further information on this can
be found in the user manual.
Connection variants for current measurement I1, I2, I3
3p 2i
(Addr. 510 = 1)
3p 2i0
(Addr. 510 = 2)
3p 3w3
(Addr. 510 = 3)
3p 3w
(Addr. 510 = 4)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
measured.
The measured values for current
measurement input I2 are
calculated.
Measurement in the 3-phase
network with unequal loading.
Measurement in the 3-phase
network with equal loading. The
measured values for current
measurement inputs I2 and I3 are
calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
2p 4w
(Addr. 510 = 5)
1p 2i
(Addr. 510 = 6)
1p 2w
(Addr. 510 = 7)
3p 1w
(Addr. 510 = 8)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
calculated.
Measured values derived from
current measurement input I3
are taken to be 0 and are not
calculated.
Measured values derived from
current measurement inputs I2 and
I3 are taken to be 0 and are not
calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
Current measuring I4
Analogue inputs
Connection variant for current
measurement (I4) via current
transformer
Current values but not power
values can be calculated for
current measurement input I4.
Load
The device has 2 analogue inputs
(terminals 32 to 37), each for a
• temperature measurement or
• residual current monitoring.
Use of the analogue inputs:
Measurement Terminal
Temperature
32/34 input 1
35/37 input 2
Residual
current
32/33/34 input 1
35/36/37 input 2
C
NOTE!
The measurement input I4 does not
require address setting on the device.
c
CAUTION!
Damage to the device / your
system due to short circuit
Inadequate insulation of the operating
equipment on the analogue inputs relative
to the mains supply circuits can lead to your
device/system being damaged.
Ensure that there is reinforced or double
insulation to the mains supply circuits!
C
NOTE!
Further information on current data and
current transformer data can be found
in the user manual.
Residual current monitoring (RCM) via I5 and I6
The UMG 96RM-E is suitable for use as a resid-
ual current monitoring device (RCM) as well as
for monitoring
• AC
• pulsing DC, and
• DC.
The UMG 96RM-E measures residual currents
in accordance with IEC/TR 60755 (2008-01),
type A and
type B.
Suitable residual current transformers with
a rated current of 30 mA are connected to
terminals 32 to 34 (
I5) and terminals 35 to
37 (
I6).
C
NOTE!
• The transformation ratios for the
residual current transformer inputs
can be individually configured via
the software.
• A connection variant
"UMG 96 RM-E with residual cur-
rent monitoring via measurement
inputs I5/I6" can be found in the
user manual.
• Measurement inputs I5 and I6 do
not require address setting on the
device.
3.
PC
UMG 96 RM-E
Ethernet
(crossover patch cable)
PC and UMG 96 RM-E require a fixed IP address..
1.
2.
DHCP server automatically assigns IP addresses to UMG 96 RM-E
and PC.
Ethernet
Ethernet
DHCP-
Server
PC
UMG 96 RM-E
Switch/
Router
(gedrehtes Patchkabel)
PC
RS232 RS232
RS485
RS485
UMG 96 RM-E
UMG 96 RM-E
Connection of the UMG 96 RM-E
via interface converter.
RS485
(gedrehtes Patchkabel)
PC
UMG 96 RM
UMG 96 RM
4.
UMG 96 RM-E
Connection of the UMG 96 RM via
an UMG 96 RM-E as gateway.
Ethernet
RS485
RS485
Establish connection to PC
The 4 most common connections for
communication between PC and device:
More details on device configuration and
communication can be found in section 14.
Recommendation for the Ethernet connection:
Use at least a CAT5 cable!
m
CAUTION!
Property damage due to
incorrect network settings
Incorrect network settings can cause faults in
the IT network!
Find out the correct Ethernet network
settings for your device from your network
administrator.
Controls and button functions
The UMG 96 RM-E is operated with buttons 1 and
2, whereby the following distinctions are made:
• Short press (button 1 or 2):
Next step (+1).
• Longer press (button 1 or 2):
Previous step (-1).
The device differentiates between display and
programming mode.
Measured values are arranged in measured value
display profiles and can be conveniently adapted
in the GridVis® software. Measured value display
profile 1 is configured at the factory.
Display mode
• Buttons 1 and 2 can be used to scroll between
the measured value indications.
• The measured value indication shows up to
3 measured values.
• A time for the automatic display change
between the measured value indications can be
configured in the GridVis® software.
C
NOTE!
More detailed information on operation, display and button functions for your device can be
found in the user manual.
Fig. UMG 96 RM-E display
Button 1
Button 2
Delivery
Mean value
CT: Current transformer
VT:
Voltage transformer
K1: Output 1
K2: Output 2
Password
Phase conductor-
Phase conductor
Summation measurement
Programming mode
Min. value NT/delivery
Max. value, HT/reference
• Hold buttons 1 and 2 depressed simultaneously
for 1 second to change between
display
mode
and
programming mode
. The text
PRG
appears in the display.
• Configure the necessary settings for the
operation of the device in programming mode.
• The programming mode can be protected with
a user password.
• Button 2 switches between the programming
menus:
1. Current transformer
2. Voltage transformer
3. Parameter list
4. TCP/IP device address
5. Subnet mask
6. Gateway address
7. Dynamic TCP/IP addressing (in/out)
The device switches from
programming mode
to
display mode
, if
• there is no button activity for 60 seconds.
• buttons 1 and 2 are pressed simultaneously for
1 second.
C
NOTE!
Changes are only applied after exiting the
programming mode.
C
NOTE!
The most important programming menus
for a quick start: TCP/IP device address,
subnet mask, gateway address (4th, 5th,
6th) and dynamic TCP/IP addressing
(on/off) (7th) via the Ethernet interface,
are explained here.
More detailed information on the
programming mode and interfaces can
be found in the user manual for the
device.
Programming mode
Example settings are selected for the device and
the PC to implement the following setttings:
Device IP address: 192.168.1.116
Subnet mask:
255.255.255.0
PC IP address:
192.168.1.117
Subnet mask:
255.255.255.0
C
NOTE!
The device is
factory-set to dynamic IP
allocation (
on) (DHCP mode).
Programming current transformers
1. Switch to programming mode.
2. The symbols for Programming mode
PRG,
and for the current transformer
CT appear.
3. Press button 1 - the first digit of the input
field for the primary current flashes.
4. Use button 2 to select the value of the
1st. digit.
5. Use button 1 to change to the 2nd. digit.
6. Use button 2 to select the value of the
2nd. digit.
7. Use button 1 to change to the 3rd. digit.
8. Use button 2 to select the value of the
3rd. digit.
9. Confirm with button 1.
10. The complete number flashes.
11. Use button 2 to select the decimal place and
thus the unit of the primary current.
12. Confirm with button 1.
13. The input range of the secondary current
flashes.
14. Set the secondary current (value 1 A or 5 A)
with button 2.
15. Confirm with button 1.
16. Exit programming mode by simultaneously
pressing buttons 1 and 2 (1 sec.). Use
button 2 to change to the input field for the
voltage transformer.
C
NOTE!
• Changes are only applied after exiting
the programming mode.
• Further information on current
transformers and current transformer
ratios can be found in the user manual.
C
NOTE!
Programming voltage transformers:
• Change to programming mode for the
voltage transformer.
• The symbols
PRG and VT appear in
the display.
• The procedure for the
voltage
transformer programming is analogous
to that of the current transformer.
Further information on voltage transformers
and voltage transformer ratios can be found
in the user manual.
Current transformer
symbol
Unit indicator
Current transformer,
primary
Programming mode
Current transformer,
secondary
Fig. "Current transformer" input field
Manual TCP/IP configuration via the Ethernet interface
Within an Ethernet network, each device has a unique
TCP/IP address that can be assigned manually or from
a DHCP server.
The 4-byte-long device address (Byte 0 to 3) is
appended within the TCP/IP configuration with the
subnet mask and gateway details.
Manual configuration (example) of the TCP/IP
device address (Addr):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and for
the current transformer
CT appear.
3. Pressing button 2 three times takes you to the
TCP/IP settings.
(Subnet mask, press
4x, gateway 5x)
4. Use button 1 to select the 1st. digit of Byte 0
(selection flashes).
5. Use button 2 to select the value.
6. Use button 1 to change to the 2nd. digit / 3rd. digit
7. Use button 2 to select the corresponding value.
8. Use button 1 to change to Byte 1
9. Select Bytes 1 to 3 in the same way.
10. Configure the subnet mask (display
SUb) and
gateway address (display
GAt) in the same way.
Designation
Byte identifier
of the address (e.g. Byte 0)
Address value, Byte 0
Fig. TCP/IP address
Byte 2, value 001.
Fig. TCP/IP address
Byte 3, value 116.
Fig. TCP/IP address,
Byte 1, value 168.
A TCP/IP address consists
of 4 bytes with the following
structure (example):
xxx.xxx.xxx.xxx
Byte 1
Byte 0
Byte 2 Byte 3
192.168.001.116
C
NOTE!
To ensure that a DHCP server does not overwrite the manual TCP/IP configuration,
deactivate
the dynamic IP allocation (dYn,
"oFF"
) (see steps 14 and 17). Then exit programming mode and
configure the TCP/IP address manually.
Dynamic TCP/IP allocation via the Ethernet interface (DHCP mode)
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address activated
(
Standard setting)
Fig. Gateway (
GAt),
Byte 0, value 192
Fig. Subnet mask (
SUb),
Byte 0, value 255
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address deactivated
With dynamic TCP/IP allocation (TCP/IP device
address, subnet mask and gateway addresses)
a network incorporates the device automatically
when the device starts up.
The reading out (or the allocation) of the dynamic
TCP/IP settings is implemented in the same way as
the "manual configuration" (see also step 16):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and
for the current transformer
CT appear.
3. Pressing button 2
six times takes you to the
dynamic TCP/IP allocation (
dYn IP).
4. Press button 1 to activate the display
"on" or
"off" (display flashes).
5. Use button 2 to select
"on" or "off".
6. Confirm your selection using the 1 button.
7. Exit programming mode by pressing buttons 1
and 2 simultaneously for 1 sec.
The dynamic IP allocation can be implemented via
the software.
NOTE!
The key symbol on the display indicates
that dynamic TCP/IP allocation is active
(
on). When the device starts up, the
DHCP server automatically allocates the
TCP/IP device address, subnet mask
and gateway address.
Fig. Mounting position,
rear view
C
NOTE!
For further information on device functions, data and assembly, see the user manual.
Suitable network systems and maximum rated voltages (DIN EN 61010-1/A1):
Fuse
Circuit breaker
C
NOTE!
As an alternative to the fuse and circuit
breaker, you can use a line safety switch.
Circuit breaker
C
NOTE!
If the metering range is exceeded, the
measurement device display shows
"EEE"
. For further information, see the
user manual.
c
WARNING!
Risk of injury due to
large currents and high
electric voltages!
Current transformers that are operated open in the
secondary side (high voltage peaks) can cause
severe bodily injuries or death.
Avoid operating current transformers when open,
short circuit transformers that are unloaded!
The voltage measurement inputs are designed for
measurements in low voltage networks, in which
rated voltages of up to
• 277 V phase to earth and 480 V phase to phase
in the 4-conductor system or
• 480 V phase to phase in the 3-conductor system
occur.
The measurement and surge voltages meet
overvoltage category 300 V CATIII.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Art. Nr
. 33.03.220
Technical data
Voltage measurement
3-phase, 4-conductor systems
with rated voltages up to
277 V/480 V (+-10%)
3-phase, 3-conductor sys-
tems, unearthed, with rated
voltages up to
IT 480 V (+-10%)
Overvoltage category
300 V CAT III
Rated surge voltage
4 kV
Protection of
voltage measurement
1 - 10 A
(With IEC / UL approval)
Measurement range L-N
0
1)
to 300 Vrms
(max. overvoltage 520 Vrms )
Measurement range L-L
0
1)
to 520 Vrms
(max. overvoltage 900 Vrms )
Resolution
0.01 V
Crest factor
2.45 (related to the measurement range)
Impedance
4 MOhm / phase
Power consumption
approx. 0.1 VA
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Frequency range of
the fundamental oscillation -
resolution
45 Hz to 65 Hz
0.01 Hz
1) ... The device determines measured values only if the Voltage
measurement input V1 voltage L1-N greater than 20 Vrms
(4-wire measurement) or a voltage L1-L2 of larger 34 Vrms
(3-wire measurement) is applied.
Current measurement I1 - I4
Nominal current
5 A
Measurement range
0 - 6 Arms
Crest factor
1.98
Resolution
0.1 mA (display 0.01 A)
Overvoltage category
300 V CAT II
Rated surge voltage
2 kV
Power consumption
approx. 0.2 VA (Ri = 5 mΩ)
Overload for 1 sec.
120 A (sinusoidal)
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Residual current monitoring I5 / I6
Nominal current
30 mArms
Measurement range
0 - 40 mArms
Triggering current
50
µ
A
Resolution
1
µ
A
Crest factor
1.414 (related to 40mA)
Burden
4 Ohm
Overload for 1 sec.
5 A
Sustained overload
1 A
Overload for 20 ms
50 A
C
NOTE!
Further technical data can be found in the
user manual for the device.
Supply voltage
Nominal range
Option 230 V:
AC 90 V - 277 V (50/60 Hz) or
DC 90 V - 250 V, 300 V CATIII
Option 24 V:
AC 24 V - 90 V (50/60 Hz) or
DC 24 V - 90 V, 150 V CATIII
Operating range
+-10% of the nominal range
Power consumption
Option 230 V: max. 7,5 VA / 4 W
Option 24 V: max. 7,5 VA / 5 W
Internal fuse,
not replaceable
Type T1A / 250 VDC / 277 VAC
according to IEC 60127
Recommended over-
current protection device for
the line protection
Option 230 V: 6-16 A
Option 24 V: 1-6 A
(Char. B)
(IEC/UL approval)
General information
Net weight
(with attached connectors)
approx. 370 g
Packaging weight
(including accessories)
approx. 950 g
Battery
Lithium battery CR2032,
3 V (approval i.a.w. UL
1642)
Service life of
background lighting
40000 h
(after this period of time
the background lighting
efficiency will reduce by
approx. 50%)
Transport and storage
The following information applies to devices which are trans-
ported or stored in the original packaging.
Free fall
1 m
Temperature
K55 (-25° C to +70° C)
Relative humidity
0 to 90% RH
Ambient coditions during operation
The device is intended for weather-protected, stationary use.
Protection class II i.a.w. IEC 60536 (VDE 0106, Part 1).
Operating temperature range
K55 (-10° C .. +55° C)
Relative humidity
0 to 75% RH
Operating altitude
0 .. 2000 m above sea level
Degree of pollution
2
Mounting position
vertical
Ventilation
Forced ventilation is
not required.
Protection against ingress
of solid foreign bodies and
water
- Front side
- Rear side
- Front with seal
IP40 i.a.w. EN60529
IP20 i.a.w. EN60529
IP54 i.a.w. EN60529
Digital inputs
3 optional digital inputs, semiconductor relays,
not short-circuit proof.
Maximum counter frequency
20 Hz
Input signal present
18V .. 28 V DC
(typical 4 mA)
Input signal not present
0 .. 5 V DC,
current less than 0.5 mA
Digital outputs
2 and 3 optional digital outputs, semiconductor relays, not
short-circuit proof.
Switching voltage
max. 33 V AC, 60 V DC
Switching current
max. 50 mAeff AC/DC
Response time
10/12 p 10 ms *
Pulse output (energy pulse)
max. 50 Hz
* Response time e.g. at 50 Hz: 200 ms + 10 ms = 210 ms
Temperature measurement input
2 optional inputs.
Update time
1 second
Connectable sensors
PT100, PT1000, KTY83,
KTY84
Total burden ( cable)
max. 4 kOhm
Cable length (digital inputs and outputs,
temperature measurement input)
Up to 30 m
Unshielded
More than 30 m
Shielded
Serial interface
RS485 - Modbus RTU/Slave
9.6 kbps, 19.2 kbps,
38.4 kbps, 57.6 kbps,
115.2 kbps
Stripping length
7 mm
Ethernet connection
Connection
RJ45
Terminal connection capacity (power supply voltage)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26 - 12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (residual current or
temperature measurement inputs and digital inputs /
outputs)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28-16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (current measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (serial interface)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28 - 16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (voltage measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.08 - 4.0 mm
2
, AWG 28-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Procedure in the event of faults
Possible fault
Cause
Remedy
No display
External fusing for the power supply voltage has
tripped.
Replace fuse.
No current display
Measurement voltage is not connected.
Connect the measuring-circuit voltage.
Measurement current is not connected.
Connect measuring-circuit current.
Current displayed is too large
or too small.
Current measurement in the wrong phase.
Check connection and correct if necessary.
Current transformer factor is incorrectly programmed. Read out and program the current transformer trans-
formation ratio at the current transformer.
The current peak value at the measurement input
was exceeded by harmonic components.
Install current transformer with a larger transforma-
tion ratio.
The current at the measurement input fell short of.
Install current transformer with a suitable transfor-
mation ratio.
Voltage displayed is too large
or too small.
Measurement in the wrong phase.
Check connection and correct if necessary.
Voltage transformer incorrectly programmed.
Read out and program the voltage transformer trans-
formation ratio at the voltage transformer.
Voltage displayed is too
small.
Overrange.
Install voltage transformers.
The peak voltage value at the measurement input has
been exceeded by harmonic components.
Caution! Ensure the measurement inputs are not
overloaded.
"EEE" in the display
See „error messages“ in the user manual.
"EEE bAt" in the display
Battery capacity is too low
Replace battery
(see "Replacing the battery" in the user manual).
Device still does not work
despite the above measures.
Device defective.
Send the device to the manufacturer for inspection
and testing along with an accurate fault description.
2
3
1
Dok Nr
. 2.040.120.1.a
Power Analyser
UMG 96 RM-E
Installation manual
Residual current monitoring (RCM)
Installation
Device settings
Power Analyser
17
18
5
6
8
7
4
The UMG 96 RM-E is a multi-functional net-
work analyser, which
• measures and monitors residual currents
(RCM) and currents at the central grounding
point (CGP). The residual current monitoring
is carried out via an external residual current
transformer (30 mA rated current) on the
current measurement inputs I5 and I6.
• measures and calculates electrical variables
such as voltage, current, power, energy,
harmonics, etc. in building installations,
on distribution units, circuit breakers and
busbar trunking systems.
• displays and saves measurement results
and transmits them via interfaces.
Install the UMG 96 RM-E in the weather-protected
front panel of switch cabinets.
Cut-out size:
92
+0.8
x 92
+0.8
mm
Ensure!
Adequate ventilation
• The device is installed
vertically!
• Observance of clearance to
adjacent components!
The UMG 96 RM-E
• is only approved for measuring current with
a current transformer.
• is intended for the connection of current
transformers with secondary currents of
../1 A and ../5 A.
• has the current transformer ratio set to 5/5 A
as standard.
L2
L3
N
L1
Load
9
19
15
16
10
13
14
11
12
L2 L3
N
L1
*1
*1
L2 L3
N L1
Last
PE
I5
I6
Deutsche V
ersion:
siehe V
or
derseite
User manual:
www
.janitza.com
Janitza electronics GmbH
Vor dem Polstück 6
D-35633 Lahnau / Germany
Support tel. +49 6441 9642-22
Fax +49 6441 9642-30
e-mail: [email protected]
Website: http://www.janitza.com
Disclaimer
The observance of the information products for
the devices is a prerequisite for safe operation
and to achieve the stipulated performance
characteristics and product characteristics.
Janitza electronics GmbH accepts no liability
for injuries to personnel, property damage
or financial losses arising due to a failure to
comply with the information products. Ensure
that your information products are accessible
and legible.
Further information can be found on our web-
site www.janitza.com at Support > Downloads.
Copyright notice
© 2016 - Janitza electronics GmbH - Lahnau.
All rights reserved. Duplication, editing,
distribution and any form of exploitation, also
as excerpts, is prohibited.
Subject to technical amendments
• Make sure that your device agrees with the
installation manual.
• Read and understand first product-related
documents.
• Keep product supporting documentation
throughout the life available and, where ap-
propriate, to pass on to subsequent users.
• Please inform yourself about device revisi-
ons and the associated adjustments to the
product-related documentation on
www.janitza.com.
Disposal
Please observe national regulations!
If disposing of individual parts, please dispose
of them in accordance with their nature and
existing country-specific regulations, for
example as:
• Electrical scrap
• Plastics
• Metals
Or, task a certified disposal business with the
scrapping.
Relevant laws, applied standards and
directives
The laws, standards and directives for the
device applied by Janitza electronic GmbH
can be found in the declaration of conformity
on our website.
General
Safety
Safety information
The installation manual does not represent a full
listing of all necessary safety measures required
for safe operation of the device.
Certain operating conditions may require further
measures. The installation manual contains
information that you must observe for your
own personal safety and to avoid damage to
property.
Symbols used:
c
This symbol is used as an addition
to the safety instructions and
warns of an electrical hazard.
m
This symbol is used as an addition
to the safety instructions and
warns of a potential hazard.
C
This symbol with the word
NOTE!
describes:
• Procedures that do not entail
any danger of injury.
• Important information,
procedures or handling steps.
Safety instructions are highlighted with
a warning triangle and shown as follows,
depending on the degree of hazard:
m
DANGER!
Indicates an immediately
threatening hazard that leads to
serious or even fatal injuries.
m
WARNING!
Indicates a potentially hazardous
situation that could lead to
serious or even fatal injuries.
m
CAUTION!
Indicates a potentially hazardous
situation that could lead to minor
injuries or damage to property.
Measures for safety
When operating electrical devices certain parts
of these devices inevitable carry dangerous
voltages. This could result in serious bodily
injury or damage to property if not handled
properly:
• Before establishing electrical connections
to the device, earth it at the ground wire
connection if there is one.
• Hazardous voltages may arise in all circuit
parts that are connected to the power supply.
• Even after disconnecting the supply voltage,
there may still be hazardous voltages
present in the device (capacitor storage).
• Do not operate equipment with current
transformer circuits when open.
• Do not exceed the limit values stipulated in
the user manual and on the rating plate - even
during testing or commissioning.
• Observe the safety and warning information in
the documents that belong to the devices!
Qualified personnel
In order to avoid injuries to personnel and
property damage, only qualified personnel with
electrical training are permitted to work on the
devices with knowledge
• of the national regulations for accident
prevention
• of safety standards
• of installation, commissioning and operation
of the device.
Proper use
The device is
• intended for installation in switch cabinets
and small installation distributors (please
observe step 3 “Assembly”).
• not intended for installation in vehicles!
The use of the device in mobile equipment
is considered to be non-standard
environmental conditions and is therefore
only permitted after separate agreement.
• not intended for installation in environments
with hazardous oils, acids, gases, vapours,
dusts, radiation, etc.
The prerequisites of faultless, safe operation
of this device are proper transport and proper
storage, set-up, installation, operation and
maintenance.
C
NOTE!
If residual currents in electrical systems
are monitored, the device (inputs I5/I6)
can trigger warning pulses if a response
threshold is exceeded. The warning pulses
can provide an alarm before a protective
device trips.
The device does not provide protection
against electric shock!
m
CAUTION!
Damage to property due to
disregard of the installation
instructions
Disregard of the installation instructions can
damage or destroy your device.
Ensure that you have enough air circulation
in your installation environment and in the
event of high environmental temperatures,
provide cooling if necessary.
Brief description of device
Assembly
Connecting the supply voltage
The supply voltage level for your device is
specified on the rating plate.
After connecting the supply voltage, an indication
appears on the display. If no indication appears,
check whether the supply voltage is within the
rated voltage range.
N
L
Fig. Connection of supply voltage.
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Device inputs that are dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
m
CAUTION!
Damage to property due to
disregard of the connection
conditions or impermissible
overvoltage!
Your device can be damaged or destroyed
by a failure to comply with the connection
conditions or by exceeding the permissible
voltage range.
Before connecting the device to the supply
voltage, please check:
•
Voltage and frequency correspond to the
details on the ratings plate! Limit values
stipulated in the user manual have been
complied with!
•
In building installations, the supply
voltage must be protected with a UL/IEC
approved circuit breaker / a fuse!
•
The isolation device
-
must be installed near the device and
in a location that is easily accessible
for the user.
-
must be labelled to identify the
respective device.
•
Do not tap the supply voltage from the
voltage transformer.
•
Provide a fuse for the neutral conductor
if the neutral conductor terminal of the
source is not grounded.
Mains systems
Three-phase, four-conductor system
with earthed neutral conductor
Three-phase, four-conductor system
with non-earthed neutral conductor
(IT networks)
Three-phase, three-conductor systems
Non-earthed
Three-phase, three-conductor systems
With earthed phase
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-L
480 VLL
U
L-L
240 VLL
Single-phase, two-conductor systems
with earthed neutral conductor
Separated single-phase,
three-conductor systems
with earthed neutral conductor
The device can be used in
• 2, 3 and 4 conductor
networks (TN, TT and
IT networks)
• residential and
industrial applications.
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
230 VLN
U
L-N
/ U
L-L
240 VLN / 480 VLL
Voltage measurement
The device has 3 voltage measurement inputs
and is suitable for various connection variants,
with direct connection or via voltage transformer.
m
CAUTION!
Danger of injury or damage to
the device
Disregard of the connection conditions for the
voltage measurement inputs can result in injuries
or to the device being damaged.
For this reason, note that:
•
The voltage measurement inputs
-
are not connected to DC voltage.
-
are equipped with a suitable, labelled
fuse and isolation device located in
the vicinity (alternative: circuit breaker)
located nearby.
-
are dangerous to touch.
•
Voltages that exceed the allowed network
rated voltages must be connected via
a voltage transformer.
•
Measured voltages and measured currents
must derive from the same network!
L2
L3
N
L1
Connection variant
3p 4w
Voltage measurement
(Addr. 509 = 0, standard setting)
Fuse (UL/IEC listed)
Current measurement I1, I2, I3
Connection variants for voltage measurement
3p 4w
(Addr. 509 = 0, standard setting)
3p 4wu
(Addr. 509 = 1)
3p 4u
(Addr. 509 = 2)
3p 2u
(Addr. 509 = 5)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measurement with 3 phase
conductors and neutral conductor.
Measurement via voltage
transformer with 3 phase
conductors and neutral conductor.
Measurement with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
Measurement via voltage
transformer with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
1p 2w1
(Addr. 509 = 4)
2p 4w
(Addr. 509 = 3)
1p 2w
(Addr. 509 = 6)
3p 1w
(Addr. 509 = 7)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measured values derived from
voltage measurement inputs V2
and V3 are taken to be 0 and are
not calculated.
System with equal loading of the
phases. The measured values of
the voltage measurement input V2
are calculated.
TN-C system with 1-phase, three-
conductor connection. Measured
values derived from voltage
measurement input V3 are taken to
be 0 and are not calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Connection variant
3p 4w Current measurement
(I1, I2, I3) via current transformer
(Addr. 510 = 0,
standard setting).
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Current measurement inputs on the device
and on the current transformer that are
dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
Earth your system! Use the earth connection
points with earthing symbols for this!
Earth the secondary windings of current
transformers and all of the metal parts of the
transformer that could be touched!
C
NOTE!
If the measurement range is exceeded,
the measurement device display shows
"EEE"
. Further information on this can
be found in the user manual.
Connection variants for current measurement I1, I2, I3
3p 2i
(Addr. 510 = 1)
3p 2i0
(Addr. 510 = 2)
3p 3w3
(Addr. 510 = 3)
3p 3w
(Addr. 510 = 4)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
measured.
The measured values for current
measurement input I2 are
calculated.
Measurement in the 3-phase
network with unequal loading.
Measurement in the 3-phase
network with equal loading. The
measured values for current
measurement inputs I2 and I3 are
calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
2p 4w
(Addr. 510 = 5)
1p 2i
(Addr. 510 = 6)
1p 2w
(Addr. 510 = 7)
3p 1w
(Addr. 510 = 8)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
calculated.
Measured values derived from
current measurement input I3
are taken to be 0 and are not
calculated.
Measured values derived from
current measurement inputs I2 and
I3 are taken to be 0 and are not
calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
Current measuring I4
Analogue inputs
Connection variant for current
measurement (I4) via current
transformer
Current values but not power
values can be calculated for
current measurement input I4.
Load
The device has 2 analogue inputs
(terminals 32 to 37), each for a
• temperature measurement or
• residual current monitoring.
Use of the analogue inputs:
Measurement Terminal
Temperature
32/34 input 1
35/37 input 2
Residual
current
32/33/34 input 1
35/36/37 input 2
C
NOTE!
The measurement input I4 does not
require address setting on the device.
c
CAUTION!
Damage to the device / your
system due to short circuit
Inadequate insulation of the operating
equipment on the analogue inputs relative
to the mains supply circuits can lead to your
device/system being damaged.
Ensure that there is reinforced or double
insulation to the mains supply circuits!
C
NOTE!
Further information on current data and
current transformer data can be found
in the user manual.
Residual current monitoring (RCM) via I5 and I6
The UMG 96RM-E is suitable for use as a resid-
ual current monitoring device (RCM) as well as
for monitoring
• AC
• pulsing DC, and
• DC.
The UMG 96RM-E measures residual currents
in accordance with IEC/TR 60755 (2008-01),
type A and
type B.
Suitable residual current transformers with
a rated current of 30 mA are connected to
terminals 32 to 34 (
I5) and terminals 35 to
37 (
I6).
C
NOTE!
• The transformation ratios for the
residual current transformer inputs
can be individually configured via
the software.
• A connection variant
"UMG 96 RM-E with residual cur-
rent monitoring via measurement
inputs I5/I6" can be found in the
user manual.
• Measurement inputs I5 and I6 do
not require address setting on the
device.
3.
PC
UMG 96 RM-E
Ethernet
(crossover patch cable)
PC and UMG 96 RM-E require a fixed IP address..
1.
2.
DHCP server automatically assigns IP addresses to UMG 96 RM-E
and PC.
Ethernet
Ethernet
DHCP-
Server
PC
UMG 96 RM-E
Switch/
Router
(gedrehtes Patchkabel)
PC
RS232 RS232
RS485
RS485
UMG 96 RM-E
UMG 96 RM-E
Connection of the UMG 96 RM-E
via interface converter.
RS485
(gedrehtes Patchkabel)
PC
UMG 96 RM
UMG 96 RM
4.
UMG 96 RM-E
Connection of the UMG 96 RM via
an UMG 96 RM-E as gateway.
Ethernet
RS485
RS485
Establish connection to PC
The 4 most common connections for
communication between PC and device:
More details on device configuration and
communication can be found in section 14.
Recommendation for the Ethernet connection:
Use at least a CAT5 cable!
m
CAUTION!
Property damage due to
incorrect network settings
Incorrect network settings can cause faults in
the IT network!
Find out the correct Ethernet network
settings for your device from your network
administrator.
Controls and button functions
The UMG 96 RM-E is operated with buttons 1 and
2, whereby the following distinctions are made:
• Short press (button 1 or 2):
Next step (+1).
• Longer press (button 1 or 2):
Previous step (-1).
The device differentiates between display and
programming mode.
Measured values are arranged in measured value
display profiles and can be conveniently adapted
in the GridVis® software. Measured value display
profile 1 is configured at the factory.
Display mode
• Buttons 1 and 2 can be used to scroll between
the measured value indications.
• The measured value indication shows up to
3 measured values.
• A time for the automatic display change
between the measured value indications can be
configured in the GridVis® software.
C
NOTE!
More detailed information on operation, display and button functions for your device can be
found in the user manual.
Fig. UMG 96 RM-E display
Button 1
Button 2
Delivery
Mean value
CT: Current transformer
VT:
Voltage transformer
K1: Output 1
K2: Output 2
Password
Phase conductor-
Phase conductor
Summation measurement
Programming mode
Min. value NT/delivery
Max. value, HT/reference
• Hold buttons 1 and 2 depressed simultaneously
for 1 second to change between
display
mode
and
programming mode
. The text
PRG
appears in the display.
• Configure the necessary settings for the
operation of the device in programming mode.
• The programming mode can be protected with
a user password.
• Button 2 switches between the programming
menus:
1. Current transformer
2. Voltage transformer
3. Parameter list
4. TCP/IP device address
5. Subnet mask
6. Gateway address
7. Dynamic TCP/IP addressing (in/out)
The device switches from
programming mode
to
display mode
, if
• there is no button activity for 60 seconds.
• buttons 1 and 2 are pressed simultaneously for
1 second.
C
NOTE!
Changes are only applied after exiting the
programming mode.
C
NOTE!
The most important programming menus
for a quick start: TCP/IP device address,
subnet mask, gateway address (4th, 5th,
6th) and dynamic TCP/IP addressing
(on/off) (7th) via the Ethernet interface,
are explained here.
More detailed information on the
programming mode and interfaces can
be found in the user manual for the
device.
Programming mode
Example settings are selected for the device and
the PC to implement the following setttings:
Device IP address: 192.168.1.116
Subnet mask:
255.255.255.0
PC IP address:
192.168.1.117
Subnet mask:
255.255.255.0
C
NOTE!
The device is
factory-set to dynamic IP
allocation (
on) (DHCP mode).
Programming current transformers
1. Switch to programming mode.
2. The symbols for Programming mode
PRG,
and for the current transformer
CT appear.
3. Press button 1 - the first digit of the input
field for the primary current flashes.
4. Use button 2 to select the value of the
1st. digit.
5. Use button 1 to change to the 2nd. digit.
6. Use button 2 to select the value of the
2nd. digit.
7. Use button 1 to change to the 3rd. digit.
8. Use button 2 to select the value of the
3rd. digit.
9. Confirm with button 1.
10. The complete number flashes.
11. Use button 2 to select the decimal place and
thus the unit of the primary current.
12. Confirm with button 1.
13. The input range of the secondary current
flashes.
14. Set the secondary current (value 1 A or 5 A)
with button 2.
15. Confirm with button 1.
16. Exit programming mode by simultaneously
pressing buttons 1 and 2 (1 sec.). Use
button 2 to change to the input field for the
voltage transformer.
C
NOTE!
• Changes are only applied after exiting
the programming mode.
• Further information on current
transformers and current transformer
ratios can be found in the user manual.
C
NOTE!
Programming voltage transformers:
• Change to programming mode for the
voltage transformer.
• The symbols
PRG and VT appear in
the display.
• The procedure for the
voltage
transformer programming is analogous
to that of the current transformer.
Further information on voltage transformers
and voltage transformer ratios can be found
in the user manual.
Current transformer
symbol
Unit indicator
Current transformer,
primary
Programming mode
Current transformer,
secondary
Fig. "Current transformer" input field
Manual TCP/IP configuration via the Ethernet interface
Within an Ethernet network, each device has a unique
TCP/IP address that can be assigned manually or from
a DHCP server.
The 4-byte-long device address (Byte 0 to 3) is
appended within the TCP/IP configuration with the
subnet mask and gateway details.
Manual configuration (example) of the TCP/IP
device address (Addr):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and for
the current transformer
CT appear.
3. Pressing button 2 three times takes you to the
TCP/IP settings.
(Subnet mask, press
4x, gateway 5x)
4. Use button 1 to select the 1st. digit of Byte 0
(selection flashes).
5. Use button 2 to select the value.
6. Use button 1 to change to the 2nd. digit / 3rd. digit
7. Use button 2 to select the corresponding value.
8. Use button 1 to change to Byte 1
9. Select Bytes 1 to 3 in the same way.
10. Configure the subnet mask (display
SUb) and
gateway address (display
GAt) in the same way.
Designation
Byte identifier
of the address (e.g. Byte 0)
Address value, Byte 0
Fig. TCP/IP address
Byte 2, value 001.
Fig. TCP/IP address
Byte 3, value 116.
Fig. TCP/IP address,
Byte 1, value 168.
A TCP/IP address consists
of 4 bytes with the following
structure (example):
xxx.xxx.xxx.xxx
Byte 1
Byte 0
Byte 2 Byte 3
192.168.001.116
C
NOTE!
To ensure that a DHCP server does not overwrite the manual TCP/IP configuration,
deactivate
the dynamic IP allocation (dYn,
"oFF"
) (see steps 14 and 17). Then exit programming mode and
configure the TCP/IP address manually.
Dynamic TCP/IP allocation via the Ethernet interface (DHCP mode)
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address activated
(
Standard setting)
Fig. Gateway (
GAt),
Byte 0, value 192
Fig. Subnet mask (
SUb),
Byte 0, value 255
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address deactivated
With dynamic TCP/IP allocation (TCP/IP device
address, subnet mask and gateway addresses)
a network incorporates the device automatically
when the device starts up.
The reading out (or the allocation) of the dynamic
TCP/IP settings is implemented in the same way as
the "manual configuration" (see also step 16):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and
for the current transformer
CT appear.
3. Pressing button 2
six times takes you to the
dynamic TCP/IP allocation (
dYn IP).
4. Press button 1 to activate the display
"on" or
"off" (display flashes).
5. Use button 2 to select
"on" or "off".
6. Confirm your selection using the 1 button.
7. Exit programming mode by pressing buttons 1
and 2 simultaneously for 1 sec.
The dynamic IP allocation can be implemented via
the software.
NOTE!
The key symbol on the display indicates
that dynamic TCP/IP allocation is active
(
on). When the device starts up, the
DHCP server automatically allocates the
TCP/IP device address, subnet mask
and gateway address.
Fig. Mounting position,
rear view
C
NOTE!
For further information on device functions, data and assembly, see the user manual.
Suitable network systems and maximum rated voltages (DIN EN 61010-1/A1):
Fuse
Circuit breaker
C
NOTE!
As an alternative to the fuse and circuit
breaker, you can use a line safety switch.
Circuit breaker
C
NOTE!
If the metering range is exceeded, the
measurement device display shows
"EEE"
. For further information, see the
user manual.
c
WARNING!
Risk of injury due to
large currents and high
electric voltages!
Current transformers that are operated open in the
secondary side (high voltage peaks) can cause
severe bodily injuries or death.
Avoid operating current transformers when open,
short circuit transformers that are unloaded!
The voltage measurement inputs are designed for
measurements in low voltage networks, in which
rated voltages of up to
• 277 V phase to earth and 480 V phase to phase
in the 4-conductor system or
• 480 V phase to phase in the 3-conductor system
occur.
The measurement and surge voltages meet
overvoltage category 300 V CATIII.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Art. Nr
. 33.03.220
Technical data
Voltage measurement
3-phase, 4-conductor systems
with rated voltages up to
277 V/480 V (+-10%)
3-phase, 3-conductor sys-
tems, unearthed, with rated
voltages up to
IT 480 V (+-10%)
Overvoltage category
300 V CAT III
Rated surge voltage
4 kV
Protection of
voltage measurement
1 - 10 A
(With IEC / UL approval)
Measurement range L-N
0
1)
to 300 Vrms
(max. overvoltage 520 Vrms )
Measurement range L-L
0
1)
to 520 Vrms
(max. overvoltage 900 Vrms )
Resolution
0.01 V
Crest factor
2.45 (related to the measurement range)
Impedance
4 MOhm / phase
Power consumption
approx. 0.1 VA
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Frequency range of
the fundamental oscillation -
resolution
45 Hz to 65 Hz
0.01 Hz
1) ... The device determines measured values only if the Voltage
measurement input V1 voltage L1-N greater than 20 Vrms
(4-wire measurement) or a voltage L1-L2 of larger 34 Vrms
(3-wire measurement) is applied.
Current measurement I1 - I4
Nominal current
5 A
Measurement range
0 - 6 Arms
Crest factor
1.98
Resolution
0.1 mA (display 0.01 A)
Overvoltage category
300 V CAT II
Rated surge voltage
2 kV
Power consumption
approx. 0.2 VA (Ri = 5 mΩ)
Overload for 1 sec.
120 A (sinusoidal)
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Residual current monitoring I5 / I6
Nominal current
30 mArms
Measurement range
0 - 40 mArms
Triggering current
50
µ
A
Resolution
1
µ
A
Crest factor
1.414 (related to 40mA)
Burden
4 Ohm
Overload for 1 sec.
5 A
Sustained overload
1 A
Overload for 20 ms
50 A
C
NOTE!
Further technical data can be found in the
user manual for the device.
Supply voltage
Nominal range
Option 230 V:
AC 90 V - 277 V (50/60 Hz) or
DC 90 V - 250 V, 300 V CATIII
Option 24 V:
AC 24 V - 90 V (50/60 Hz) or
DC 24 V - 90 V, 150 V CATIII
Operating range
+-10% of the nominal range
Power consumption
Option 230 V: max. 7,5 VA / 4 W
Option 24 V: max. 7,5 VA / 5 W
Internal fuse,
not replaceable
Type T1A / 250 VDC / 277 VAC
according to IEC 60127
Recommended over-
current protection device for
the line protection
Option 230 V: 6-16 A
Option 24 V: 1-6 A
(Char. B)
(IEC/UL approval)
General information
Net weight
(with attached connectors)
approx. 370 g
Packaging weight
(including accessories)
approx. 950 g
Battery
Lithium battery CR2032,
3 V (approval i.a.w. UL
1642)
Service life of
background lighting
40000 h
(after this period of time
the background lighting
efficiency will reduce by
approx. 50%)
Transport and storage
The following information applies to devices which are trans-
ported or stored in the original packaging.
Free fall
1 m
Temperature
K55 (-25° C to +70° C)
Relative humidity
0 to 90% RH
Ambient coditions during operation
The device is intended for weather-protected, stationary use.
Protection class II i.a.w. IEC 60536 (VDE 0106, Part 1).
Operating temperature range
K55 (-10° C .. +55° C)
Relative humidity
0 to 75% RH
Operating altitude
0 .. 2000 m above sea level
Degree of pollution
2
Mounting position
vertical
Ventilation
Forced ventilation is
not required.
Protection against ingress
of solid foreign bodies and
water
- Front side
- Rear side
- Front with seal
IP40 i.a.w. EN60529
IP20 i.a.w. EN60529
IP54 i.a.w. EN60529
Digital inputs
3 optional digital inputs, semiconductor relays,
not short-circuit proof.
Maximum counter frequency
20 Hz
Input signal present
18V .. 28 V DC
(typical 4 mA)
Input signal not present
0 .. 5 V DC,
current less than 0.5 mA
Digital outputs
2 and 3 optional digital outputs, semiconductor relays, not
short-circuit proof.
Switching voltage
max. 33 V AC, 60 V DC
Switching current
max. 50 mAeff AC/DC
Response time
10/12 p 10 ms *
Pulse output (energy pulse)
max. 50 Hz
* Response time e.g. at 50 Hz: 200 ms + 10 ms = 210 ms
Temperature measurement input
2 optional inputs.
Update time
1 second
Connectable sensors
PT100, PT1000, KTY83,
KTY84
Total burden ( cable)
max. 4 kOhm
Cable length (digital inputs and outputs,
temperature measurement input)
Up to 30 m
Unshielded
More than 30 m
Shielded
Serial interface
RS485 - Modbus RTU/Slave
9.6 kbps, 19.2 kbps,
38.4 kbps, 57.6 kbps,
115.2 kbps
Stripping length
7 mm
Ethernet connection
Connection
RJ45
Terminal connection capacity (power supply voltage)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26 - 12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (residual current or
temperature measurement inputs and digital inputs /
outputs)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28-16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (current measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (serial interface)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28 - 16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (voltage measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.08 - 4.0 mm
2
, AWG 28-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Procedure in the event of faults
Possible fault
Cause
Remedy
No display
External fusing for the power supply voltage has
tripped.
Replace fuse.
No current display
Measurement voltage is not connected.
Connect the measuring-circuit voltage.
Measurement current is not connected.
Connect measuring-circuit current.
Current displayed is too large
or too small.
Current measurement in the wrong phase.
Check connection and correct if necessary.
Current transformer factor is incorrectly programmed. Read out and program the current transformer trans-
formation ratio at the current transformer.
The current peak value at the measurement input
was exceeded by harmonic components.
Install current transformer with a larger transforma-
tion ratio.
The current at the measurement input fell short of.
Install current transformer with a suitable transfor-
mation ratio.
Voltage displayed is too large
or too small.
Measurement in the wrong phase.
Check connection and correct if necessary.
Voltage transformer incorrectly programmed.
Read out and program the voltage transformer trans-
formation ratio at the voltage transformer.
Voltage displayed is too
small.
Overrange.
Install voltage transformers.
The peak voltage value at the measurement input has
been exceeded by harmonic components.
Caution! Ensure the measurement inputs are not
overloaded.
"EEE" in the display
See „error messages“ in the user manual.
"EEE bAt" in the display
Battery capacity is too low
Replace battery
(see "Replacing the battery" in the user manual).
Device still does not work
despite the above measures.
Device defective.
Send the device to the manufacturer for inspection
and testing along with an accurate fault description.
2
3
1
Dok Nr
. 2.040.120.1.a
Power Analyser
UMG 96 RM-E
Installation manual
Residual current monitoring (RCM)
Installation
Device settings
Power Analyser
17
18
5
6
8
7
4
The UMG 96 RM-E is a multi-functional net-
work analyser, which
• measures and monitors residual currents
(RCM) and currents at the central grounding
point (CGP). The residual current monitoring
is carried out via an external residual current
transformer (30 mA rated current) on the
current measurement inputs I5 and I6.
• measures and calculates electrical variables
such as voltage, current, power, energy,
harmonics, etc. in building installations,
on distribution units, circuit breakers and
busbar trunking systems.
• displays and saves measurement results
and transmits them via interfaces.
Install the UMG 96 RM-E in the weather-protected
front panel of switch cabinets.
Cut-out size:
92
+0.8
x 92
+0.8
mm
Ensure!
Adequate ventilation
• The device is installed
vertically!
• Observance of clearance to
adjacent components!
The UMG 96 RM-E
• is only approved for measuring current with
a current transformer.
• is intended for the connection of current
transformers with secondary currents of
../1 A and ../5 A.
• has the current transformer ratio set to 5/5 A
as standard.
L2
L3
N
L1
Load
9
19
15
16
10
13
14
11
12
L2 L3
N
L1
*1
*1
L2 L3
N L1
Last
PE
I5
I6
Deutsche V
ersion:
siehe V
or
derseite
User manual:
www
.janitza.com
Janitza electronics GmbH
Vor dem Polstück 6
D-35633 Lahnau / Germany
Support tel. +49 6441 9642-22
Fax +49 6441 9642-30
e-mail: [email protected]
Website: http://www.janitza.com
Disclaimer
The observance of the information products for
the devices is a prerequisite for safe operation
and to achieve the stipulated performance
characteristics and product characteristics.
Janitza electronics GmbH accepts no liability
for injuries to personnel, property damage
or financial losses arising due to a failure to
comply with the information products. Ensure
that your information products are accessible
and legible.
Further information can be found on our web-
site www.janitza.com at Support > Downloads.
Copyright notice
© 2016 - Janitza electronics GmbH - Lahnau.
All rights reserved. Duplication, editing,
distribution and any form of exploitation, also
as excerpts, is prohibited.
Subject to technical amendments
• Make sure that your device agrees with the
installation manual.
• Read and understand first product-related
documents.
• Keep product supporting documentation
throughout the life available and, where ap-
propriate, to pass on to subsequent users.
• Please inform yourself about device revisi-
ons and the associated adjustments to the
product-related documentation on
www.janitza.com.
Disposal
Please observe national regulations!
If disposing of individual parts, please dispose
of them in accordance with their nature and
existing country-specific regulations, for
example as:
• Electrical scrap
• Plastics
• Metals
Or, task a certified disposal business with the
scrapping.
Relevant laws, applied standards and
directives
The laws, standards and directives for the
device applied by Janitza electronic GmbH
can be found in the declaration of conformity
on our website.
General
Safety
Safety information
The installation manual does not represent a full
listing of all necessary safety measures required
for safe operation of the device.
Certain operating conditions may require further
measures. The installation manual contains
information that you must observe for your
own personal safety and to avoid damage to
property.
Symbols used:
c
This symbol is used as an addition
to the safety instructions and
warns of an electrical hazard.
m
This symbol is used as an addition
to the safety instructions and
warns of a potential hazard.
C
This symbol with the word
NOTE!
describes:
• Procedures that do not entail
any danger of injury.
• Important information,
procedures or handling steps.
Safety instructions are highlighted with
a warning triangle and shown as follows,
depending on the degree of hazard:
m
DANGER!
Indicates an immediately
threatening hazard that leads to
serious or even fatal injuries.
m
WARNING!
Indicates a potentially hazardous
situation that could lead to
serious or even fatal injuries.
m
CAUTION!
Indicates a potentially hazardous
situation that could lead to minor
injuries or damage to property.
Measures for safety
When operating electrical devices certain parts
of these devices inevitable carry dangerous
voltages. This could result in serious bodily
injury or damage to property if not handled
properly:
• Before establishing electrical connections
to the device, earth it at the ground wire
connection if there is one.
• Hazardous voltages may arise in all circuit
parts that are connected to the power supply.
• Even after disconnecting the supply voltage,
there may still be hazardous voltages
present in the device (capacitor storage).
• Do not operate equipment with current
transformer circuits when open.
• Do not exceed the limit values stipulated in
the user manual and on the rating plate - even
during testing or commissioning.
• Observe the safety and warning information in
the documents that belong to the devices!
Qualified personnel
In order to avoid injuries to personnel and
property damage, only qualified personnel with
electrical training are permitted to work on the
devices with knowledge
• of the national regulations for accident
prevention
• of safety standards
• of installation, commissioning and operation
of the device.
Proper use
The device is
• intended for installation in switch cabinets
and small installation distributors (please
observe step 3 “Assembly”).
• not intended for installation in vehicles!
The use of the device in mobile equipment
is considered to be non-standard
environmental conditions and is therefore
only permitted after separate agreement.
• not intended for installation in environments
with hazardous oils, acids, gases, vapours,
dusts, radiation, etc.
The prerequisites of faultless, safe operation
of this device are proper transport and proper
storage, set-up, installation, operation and
maintenance.
C
NOTE!
If residual currents in electrical systems
are monitored, the device (inputs I5/I6)
can trigger warning pulses if a response
threshold is exceeded. The warning pulses
can provide an alarm before a protective
device trips.
The device does not provide protection
against electric shock!
m
CAUTION!
Damage to property due to
disregard of the installation
instructions
Disregard of the installation instructions can
damage or destroy your device.
Ensure that you have enough air circulation
in your installation environment and in the
event of high environmental temperatures,
provide cooling if necessary.
Brief description of device
Assembly
Connecting the supply voltage
The supply voltage level for your device is
specified on the rating plate.
After connecting the supply voltage, an indication
appears on the display. If no indication appears,
check whether the supply voltage is within the
rated voltage range.
N
L
Fig. Connection of supply voltage.
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Device inputs that are dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
m
CAUTION!
Damage to property due to
disregard of the connection
conditions or impermissible
overvoltage!
Your device can be damaged or destroyed
by a failure to comply with the connection
conditions or by exceeding the permissible
voltage range.
Before connecting the device to the supply
voltage, please check:
•
Voltage and frequency correspond to the
details on the ratings plate! Limit values
stipulated in the user manual have been
complied with!
•
In building installations, the supply
voltage must be protected with a UL/IEC
approved circuit breaker / a fuse!
•
The isolation device
-
must be installed near the device and
in a location that is easily accessible
for the user.
-
must be labelled to identify the
respective device.
•
Do not tap the supply voltage from the
voltage transformer.
•
Provide a fuse for the neutral conductor
if the neutral conductor terminal of the
source is not grounded.
Mains systems
Three-phase, four-conductor system
with earthed neutral conductor
Three-phase, four-conductor system
with non-earthed neutral conductor
(IT networks)
Three-phase, three-conductor systems
Non-earthed
Three-phase, three-conductor systems
With earthed phase
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-L
480 VLL
U
L-L
240 VLL
Single-phase, two-conductor systems
with earthed neutral conductor
Separated single-phase,
three-conductor systems
with earthed neutral conductor
The device can be used in
• 2, 3 and 4 conductor
networks (TN, TT and
IT networks)
• residential and
industrial applications.
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
230 VLN
U
L-N
/ U
L-L
240 VLN / 480 VLL
Voltage measurement
The device has 3 voltage measurement inputs
and is suitable for various connection variants,
with direct connection or via voltage transformer.
m
CAUTION!
Danger of injury or damage to
the device
Disregard of the connection conditions for the
voltage measurement inputs can result in injuries
or to the device being damaged.
For this reason, note that:
•
The voltage measurement inputs
-
are not connected to DC voltage.
-
are equipped with a suitable, labelled
fuse and isolation device located in
the vicinity (alternative: circuit breaker)
located nearby.
-
are dangerous to touch.
•
Voltages that exceed the allowed network
rated voltages must be connected via
a voltage transformer.
•
Measured voltages and measured currents
must derive from the same network!
L2
L3
N
L1
Connection variant
3p 4w
Voltage measurement
(Addr. 509 = 0, standard setting)
Fuse (UL/IEC listed)
Current measurement I1, I2, I3
Connection variants for voltage measurement
3p 4w
(Addr. 509 = 0, standard setting)
3p 4wu
(Addr. 509 = 1)
3p 4u
(Addr. 509 = 2)
3p 2u
(Addr. 509 = 5)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measurement with 3 phase
conductors and neutral conductor.
Measurement via voltage
transformer with 3 phase
conductors and neutral conductor.
Measurement with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
Measurement via voltage
transformer with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
1p 2w1
(Addr. 509 = 4)
2p 4w
(Addr. 509 = 3)
1p 2w
(Addr. 509 = 6)
3p 1w
(Addr. 509 = 7)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measured values derived from
voltage measurement inputs V2
and V3 are taken to be 0 and are
not calculated.
System with equal loading of the
phases. The measured values of
the voltage measurement input V2
are calculated.
TN-C system with 1-phase, three-
conductor connection. Measured
values derived from voltage
measurement input V3 are taken to
be 0 and are not calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Connection variant
3p 4w Current measurement
(I1, I2, I3) via current transformer
(Addr. 510 = 0,
standard setting).
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Current measurement inputs on the device
and on the current transformer that are
dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
Earth your system! Use the earth connection
points with earthing symbols for this!
Earth the secondary windings of current
transformers and all of the metal parts of the
transformer that could be touched!
C
NOTE!
If the measurement range is exceeded,
the measurement device display shows
"EEE"
. Further information on this can
be found in the user manual.
Connection variants for current measurement I1, I2, I3
3p 2i
(Addr. 510 = 1)
3p 2i0
(Addr. 510 = 2)
3p 3w3
(Addr. 510 = 3)
3p 3w
(Addr. 510 = 4)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
measured.
The measured values for current
measurement input I2 are
calculated.
Measurement in the 3-phase
network with unequal loading.
Measurement in the 3-phase
network with equal loading. The
measured values for current
measurement inputs I2 and I3 are
calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
2p 4w
(Addr. 510 = 5)
1p 2i
(Addr. 510 = 6)
1p 2w
(Addr. 510 = 7)
3p 1w
(Addr. 510 = 8)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
calculated.
Measured values derived from
current measurement input I3
are taken to be 0 and are not
calculated.
Measured values derived from
current measurement inputs I2 and
I3 are taken to be 0 and are not
calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
Current measuring I4
Analogue inputs
Connection variant for current
measurement (I4) via current
transformer
Current values but not power
values can be calculated for
current measurement input I4.
Load
The device has 2 analogue inputs
(terminals 32 to 37), each for a
• temperature measurement or
• residual current monitoring.
Use of the analogue inputs:
Measurement Terminal
Temperature
32/34 input 1
35/37 input 2
Residual
current
32/33/34 input 1
35/36/37 input 2
C
NOTE!
The measurement input I4 does not
require address setting on the device.
c
CAUTION!
Damage to the device / your
system due to short circuit
Inadequate insulation of the operating
equipment on the analogue inputs relative
to the mains supply circuits can lead to your
device/system being damaged.
Ensure that there is reinforced or double
insulation to the mains supply circuits!
C
NOTE!
Further information on current data and
current transformer data can be found
in the user manual.
Residual current monitoring (RCM) via I5 and I6
The UMG 96RM-E is suitable for use as a resid-
ual current monitoring device (RCM) as well as
for monitoring
• AC
• pulsing DC, and
• DC.
The UMG 96RM-E measures residual currents
in accordance with IEC/TR 60755 (2008-01),
type A and
type B.
Suitable residual current transformers with
a rated current of 30 mA are connected to
terminals 32 to 34 (
I5) and terminals 35 to
37 (
I6).
C
NOTE!
• The transformation ratios for the
residual current transformer inputs
can be individually configured via
the software.
• A connection variant
"UMG 96 RM-E with residual cur-
rent monitoring via measurement
inputs I5/I6" can be found in the
user manual.
• Measurement inputs I5 and I6 do
not require address setting on the
device.
3.
PC
UMG 96 RM-E
Ethernet
(crossover patch cable)
PC and UMG 96 RM-E require a fixed IP address..
1.
2.
DHCP server automatically assigns IP addresses to UMG 96 RM-E
and PC.
Ethernet
Ethernet
DHCP-
Server
PC
UMG 96 RM-E
Switch/
Router
(gedrehtes Patchkabel)
PC
RS232 RS232
RS485
RS485
UMG 96 RM-E
UMG 96 RM-E
Connection of the UMG 96 RM-E
via interface converter.
RS485
(gedrehtes Patchkabel)
PC
UMG 96 RM
UMG 96 RM
4.
UMG 96 RM-E
Connection of the UMG 96 RM via
an UMG 96 RM-E as gateway.
Ethernet
RS485
RS485
Establish connection to PC
The 4 most common connections for
communication between PC and device:
More details on device configuration and
communication can be found in section 14.
Recommendation for the Ethernet connection:
Use at least a CAT5 cable!
m
CAUTION!
Property damage due to
incorrect network settings
Incorrect network settings can cause faults in
the IT network!
Find out the correct Ethernet network
settings for your device from your network
administrator.
Controls and button functions
The UMG 96 RM-E is operated with buttons 1 and
2, whereby the following distinctions are made:
• Short press (button 1 or 2):
Next step (+1).
• Longer press (button 1 or 2):
Previous step (-1).
The device differentiates between display and
programming mode.
Measured values are arranged in measured value
display profiles and can be conveniently adapted
in the GridVis® software. Measured value display
profile 1 is configured at the factory.
Display mode
• Buttons 1 and 2 can be used to scroll between
the measured value indications.
• The measured value indication shows up to
3 measured values.
• A time for the automatic display change
between the measured value indications can be
configured in the GridVis® software.
C
NOTE!
More detailed information on operation, display and button functions for your device can be
found in the user manual.
Fig. UMG 96 RM-E display
Button 1
Button 2
Delivery
Mean value
CT: Current transformer
VT:
Voltage transformer
K1: Output 1
K2: Output 2
Password
Phase conductor-
Phase conductor
Summation measurement
Programming mode
Min. value NT/delivery
Max. value, HT/reference
• Hold buttons 1 and 2 depressed simultaneously
for 1 second to change between
display
mode
and
programming mode
. The text
PRG
appears in the display.
• Configure the necessary settings for the
operation of the device in programming mode.
• The programming mode can be protected with
a user password.
• Button 2 switches between the programming
menus:
1. Current transformer
2. Voltage transformer
3. Parameter list
4. TCP/IP device address
5. Subnet mask
6. Gateway address
7. Dynamic TCP/IP addressing (in/out)
The device switches from
programming mode
to
display mode
, if
• there is no button activity for 60 seconds.
• buttons 1 and 2 are pressed simultaneously for
1 second.
C
NOTE!
Changes are only applied after exiting the
programming mode.
C
NOTE!
The most important programming menus
for a quick start: TCP/IP device address,
subnet mask, gateway address (4th, 5th,
6th) and dynamic TCP/IP addressing
(on/off) (7th) via the Ethernet interface,
are explained here.
More detailed information on the
programming mode and interfaces can
be found in the user manual for the
device.
Programming mode
Example settings are selected for the device and
the PC to implement the following setttings:
Device IP address: 192.168.1.116
Subnet mask:
255.255.255.0
PC IP address:
192.168.1.117
Subnet mask:
255.255.255.0
C
NOTE!
The device is
factory-set to dynamic IP
allocation (
on) (DHCP mode).
Programming current transformers
1. Switch to programming mode.
2. The symbols for Programming mode
PRG,
and for the current transformer
CT appear.
3. Press button 1 - the first digit of the input
field for the primary current flashes.
4. Use button 2 to select the value of the
1st. digit.
5. Use button 1 to change to the 2nd. digit.
6. Use button 2 to select the value of the
2nd. digit.
7. Use button 1 to change to the 3rd. digit.
8. Use button 2 to select the value of the
3rd. digit.
9. Confirm with button 1.
10. The complete number flashes.
11. Use button 2 to select the decimal place and
thus the unit of the primary current.
12. Confirm with button 1.
13. The input range of the secondary current
flashes.
14. Set the secondary current (value 1 A or 5 A)
with button 2.
15. Confirm with button 1.
16. Exit programming mode by simultaneously
pressing buttons 1 and 2 (1 sec.). Use
button 2 to change to the input field for the
voltage transformer.
C
NOTE!
• Changes are only applied after exiting
the programming mode.
• Further information on current
transformers and current transformer
ratios can be found in the user manual.
C
NOTE!
Programming voltage transformers:
• Change to programming mode for the
voltage transformer.
• The symbols
PRG and VT appear in
the display.
• The procedure for the
voltage
transformer programming is analogous
to that of the current transformer.
Further information on voltage transformers
and voltage transformer ratios can be found
in the user manual.
Current transformer
symbol
Unit indicator
Current transformer,
primary
Programming mode
Current transformer,
secondary
Fig. "Current transformer" input field
Manual TCP/IP configuration via the Ethernet interface
Within an Ethernet network, each device has a unique
TCP/IP address that can be assigned manually or from
a DHCP server.
The 4-byte-long device address (Byte 0 to 3) is
appended within the TCP/IP configuration with the
subnet mask and gateway details.
Manual configuration (example) of the TCP/IP
device address (Addr):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and for
the current transformer
CT appear.
3. Pressing button 2 three times takes you to the
TCP/IP settings.
(Subnet mask, press
4x, gateway 5x)
4. Use button 1 to select the 1st. digit of Byte 0
(selection flashes).
5. Use button 2 to select the value.
6. Use button 1 to change to the 2nd. digit / 3rd. digit
7. Use button 2 to select the corresponding value.
8. Use button 1 to change to Byte 1
9. Select Bytes 1 to 3 in the same way.
10. Configure the subnet mask (display
SUb) and
gateway address (display
GAt) in the same way.
Designation
Byte identifier
of the address (e.g. Byte 0)
Address value, Byte 0
Fig. TCP/IP address
Byte 2, value 001.
Fig. TCP/IP address
Byte 3, value 116.
Fig. TCP/IP address,
Byte 1, value 168.
A TCP/IP address consists
of 4 bytes with the following
structure (example):
xxx.xxx.xxx.xxx
Byte 1
Byte 0
Byte 2 Byte 3
192.168.001.116
C
NOTE!
To ensure that a DHCP server does not overwrite the manual TCP/IP configuration,
deactivate
the dynamic IP allocation (dYn,
"oFF"
) (see steps 14 and 17). Then exit programming mode and
configure the TCP/IP address manually.
Dynamic TCP/IP allocation via the Ethernet interface (DHCP mode)
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address activated
(
Standard setting)
Fig. Gateway (
GAt),
Byte 0, value 192
Fig. Subnet mask (
SUb),
Byte 0, value 255
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address deactivated
With dynamic TCP/IP allocation (TCP/IP device
address, subnet mask and gateway addresses)
a network incorporates the device automatically
when the device starts up.
The reading out (or the allocation) of the dynamic
TCP/IP settings is implemented in the same way as
the "manual configuration" (see also step 16):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and
for the current transformer
CT appear.
3. Pressing button 2
six times takes you to the
dynamic TCP/IP allocation (
dYn IP).
4. Press button 1 to activate the display
"on" or
"off" (display flashes).
5. Use button 2 to select
"on" or "off".
6. Confirm your selection using the 1 button.
7. Exit programming mode by pressing buttons 1
and 2 simultaneously for 1 sec.
The dynamic IP allocation can be implemented via
the software.
NOTE!
The key symbol on the display indicates
that dynamic TCP/IP allocation is active
(
on). When the device starts up, the
DHCP server automatically allocates the
TCP/IP device address, subnet mask
and gateway address.
Fig. Mounting position,
rear view
C
NOTE!
For further information on device functions, data and assembly, see the user manual.
Suitable network systems and maximum rated voltages (DIN EN 61010-1/A1):
Fuse
Circuit breaker
C
NOTE!
As an alternative to the fuse and circuit
breaker, you can use a line safety switch.
Circuit breaker
C
NOTE!
If the metering range is exceeded, the
measurement device display shows
"EEE"
. For further information, see the
user manual.
c
WARNING!
Risk of injury due to
large currents and high
electric voltages!
Current transformers that are operated open in the
secondary side (high voltage peaks) can cause
severe bodily injuries or death.
Avoid operating current transformers when open,
short circuit transformers that are unloaded!
The voltage measurement inputs are designed for
measurements in low voltage networks, in which
rated voltages of up to
• 277 V phase to earth and 480 V phase to phase
in the 4-conductor system or
• 480 V phase to phase in the 3-conductor system
occur.
The measurement and surge voltages meet
overvoltage category 300 V CATIII.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Art. Nr
. 33.03.220
Technical data
Voltage measurement
3-phase, 4-conductor systems
with rated voltages up to
277 V/480 V (+-10%)
3-phase, 3-conductor sys-
tems, unearthed, with rated
voltages up to
IT 480 V (+-10%)
Overvoltage category
300 V CAT III
Rated surge voltage
4 kV
Protection of
voltage measurement
1 - 10 A
(With IEC / UL approval)
Measurement range L-N
0
1)
to 300 Vrms
(max. overvoltage 520 Vrms )
Measurement range L-L
0
1)
to 520 Vrms
(max. overvoltage 900 Vrms )
Resolution
0.01 V
Crest factor
2.45 (related to the measurement range)
Impedance
4 MOhm / phase
Power consumption
approx. 0.1 VA
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Frequency range of
the fundamental oscillation -
resolution
45 Hz to 65 Hz
0.01 Hz
1) ... The device determines measured values only if the Voltage
measurement input V1 voltage L1-N greater than 20 Vrms
(4-wire measurement) or a voltage L1-L2 of larger 34 Vrms
(3-wire measurement) is applied.
Current measurement I1 - I4
Nominal current
5 A
Measurement range
0 - 6 Arms
Crest factor
1.98
Resolution
0.1 mA (display 0.01 A)
Overvoltage category
300 V CAT II
Rated surge voltage
2 kV
Power consumption
approx. 0.2 VA (Ri = 5 mΩ)
Overload for 1 sec.
120 A (sinusoidal)
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Residual current monitoring I5 / I6
Nominal current
30 mArms
Measurement range
0 - 40 mArms
Triggering current
50
µ
A
Resolution
1
µ
A
Crest factor
1.414 (related to 40mA)
Burden
4 Ohm
Overload for 1 sec.
5 A
Sustained overload
1 A
Overload for 20 ms
50 A
C
NOTE!
Further technical data can be found in the
user manual for the device.
Supply voltage
Nominal range
Option 230 V:
AC 90 V - 277 V (50/60 Hz) or
DC 90 V - 250 V, 300 V CATIII
Option 24 V:
AC 24 V - 90 V (50/60 Hz) or
DC 24 V - 90 V, 150 V CATIII
Operating range
+-10% of the nominal range
Power consumption
Option 230 V: max. 7,5 VA / 4 W
Option 24 V: max. 7,5 VA / 5 W
Internal fuse,
not replaceable
Type T1A / 250 VDC / 277 VAC
according to IEC 60127
Recommended over-
current protection device for
the line protection
Option 230 V: 6-16 A
Option 24 V: 1-6 A
(Char. B)
(IEC/UL approval)
General information
Net weight
(with attached connectors)
approx. 370 g
Packaging weight
(including accessories)
approx. 950 g
Battery
Lithium battery CR2032,
3 V (approval i.a.w. UL
1642)
Service life of
background lighting
40000 h
(after this period of time
the background lighting
efficiency will reduce by
approx. 50%)
Transport and storage
The following information applies to devices which are trans-
ported or stored in the original packaging.
Free fall
1 m
Temperature
K55 (-25° C to +70° C)
Relative humidity
0 to 90% RH
Ambient coditions during operation
The device is intended for weather-protected, stationary use.
Protection class II i.a.w. IEC 60536 (VDE 0106, Part 1).
Operating temperature range
K55 (-10° C .. +55° C)
Relative humidity
0 to 75% RH
Operating altitude
0 .. 2000 m above sea level
Degree of pollution
2
Mounting position
vertical
Ventilation
Forced ventilation is
not required.
Protection against ingress
of solid foreign bodies and
water
- Front side
- Rear side
- Front with seal
IP40 i.a.w. EN60529
IP20 i.a.w. EN60529
IP54 i.a.w. EN60529
Digital inputs
3 optional digital inputs, semiconductor relays,
not short-circuit proof.
Maximum counter frequency
20 Hz
Input signal present
18V .. 28 V DC
(typical 4 mA)
Input signal not present
0 .. 5 V DC,
current less than 0.5 mA
Digital outputs
2 and 3 optional digital outputs, semiconductor relays, not
short-circuit proof.
Switching voltage
max. 33 V AC, 60 V DC
Switching current
max. 50 mAeff AC/DC
Response time
10/12 p 10 ms *
Pulse output (energy pulse)
max. 50 Hz
* Response time e.g. at 50 Hz: 200 ms + 10 ms = 210 ms
Temperature measurement input
2 optional inputs.
Update time
1 second
Connectable sensors
PT100, PT1000, KTY83,
KTY84
Total burden ( cable)
max. 4 kOhm
Cable length (digital inputs and outputs,
temperature measurement input)
Up to 30 m
Unshielded
More than 30 m
Shielded
Serial interface
RS485 - Modbus RTU/Slave
9.6 kbps, 19.2 kbps,
38.4 kbps, 57.6 kbps,
115.2 kbps
Stripping length
7 mm
Ethernet connection
Connection
RJ45
Terminal connection capacity (power supply voltage)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26 - 12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (residual current or
temperature measurement inputs and digital inputs /
outputs)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28-16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (current measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (serial interface)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28 - 16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (voltage measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.08 - 4.0 mm
2
, AWG 28-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Procedure in the event of faults
Possible fault
Cause
Remedy
No display
External fusing for the power supply voltage has
tripped.
Replace fuse.
No current display
Measurement voltage is not connected.
Connect the measuring-circuit voltage.
Measurement current is not connected.
Connect measuring-circuit current.
Current displayed is too large
or too small.
Current measurement in the wrong phase.
Check connection and correct if necessary.
Current transformer factor is incorrectly programmed. Read out and program the current transformer trans-
formation ratio at the current transformer.
The current peak value at the measurement input
was exceeded by harmonic components.
Install current transformer with a larger transforma-
tion ratio.
The current at the measurement input fell short of.
Install current transformer with a suitable transfor-
mation ratio.
Voltage displayed is too large
or too small.
Measurement in the wrong phase.
Check connection and correct if necessary.
Voltage transformer incorrectly programmed.
Read out and program the voltage transformer trans-
formation ratio at the voltage transformer.
Voltage displayed is too
small.
Overrange.
Install voltage transformers.
The peak voltage value at the measurement input has
been exceeded by harmonic components.
Caution! Ensure the measurement inputs are not
overloaded.
"EEE" in the display
See „error messages“ in the user manual.
"EEE bAt" in the display
Battery capacity is too low
Replace battery
(see "Replacing the battery" in the user manual).
Device still does not work
despite the above measures.
Device defective.
Send the device to the manufacturer for inspection
and testing along with an accurate fault description.
2
3
1
Dok Nr
. 2.040.120.1.a
Power Analyser
UMG 96 RM-E
Installation manual
Residual current monitoring (RCM)
Installation
Device settings
Power Analyser
17
18
5
6
8
7
4
The UMG 96 RM-E is a multi-functional net-
work analyser, which
• measures and monitors residual currents
(RCM) and currents at the central grounding
point (CGP). The residual current monitoring
is carried out via an external residual current
transformer (30 mA rated current) on the
current measurement inputs I5 and I6.
• measures and calculates electrical variables
such as voltage, current, power, energy,
harmonics, etc. in building installations,
on distribution units, circuit breakers and
busbar trunking systems.
• displays and saves measurement results
and transmits them via interfaces.
Install the UMG 96 RM-E in the weather-protected
front panel of switch cabinets.
Cut-out size:
92
+0.8
x 92
+0.8
mm
Ensure!
Adequate ventilation
• The device is installed
vertically!
• Observance of clearance to
adjacent components!
The UMG 96 RM-E
• is only approved for measuring current with
a current transformer.
• is intended for the connection of current
transformers with secondary currents of
../1 A and ../5 A.
• has the current transformer ratio set to 5/5 A
as standard.
L2
L3
N
L1
Load
9
19
15
16
10
13
14
11
12
L2 L3
N
L1
*1
*1
L2 L3
N L1
Last
PE
I5
I6
Deutsche V
ersion:
siehe V
or
derseite
User manual:
www
.janitza.com
Janitza electronics GmbH
Vor dem Polstück 6
D-35633 Lahnau / Germany
Support tel. +49 6441 9642-22
Fax +49 6441 9642-30
e-mail: [email protected]
Website: http://www.janitza.com
Disclaimer
The observance of the information products for
the devices is a prerequisite for safe operation
and to achieve the stipulated performance
characteristics and product characteristics.
Janitza electronics GmbH accepts no liability
for injuries to personnel, property damage
or financial losses arising due to a failure to
comply with the information products. Ensure
that your information products are accessible
and legible.
Further information can be found on our web-
site www.janitza.com at Support > Downloads.
Copyright notice
© 2016 - Janitza electronics GmbH - Lahnau.
All rights reserved. Duplication, editing,
distribution and any form of exploitation, also
as excerpts, is prohibited.
Subject to technical amendments
• Make sure that your device agrees with the
installation manual.
• Read and understand first product-related
documents.
• Keep product supporting documentation
throughout the life available and, where ap-
propriate, to pass on to subsequent users.
• Please inform yourself about device revisi-
ons and the associated adjustments to the
product-related documentation on
www.janitza.com.
Disposal
Please observe national regulations!
If disposing of individual parts, please dispose
of them in accordance with their nature and
existing country-specific regulations, for
example as:
• Electrical scrap
• Plastics
• Metals
Or, task a certified disposal business with the
scrapping.
Relevant laws, applied standards and
directives
The laws, standards and directives for the
device applied by Janitza electronic GmbH
can be found in the declaration of conformity
on our website.
General
Safety
Safety information
The installation manual does not represent a full
listing of all necessary safety measures required
for safe operation of the device.
Certain operating conditions may require further
measures. The installation manual contains
information that you must observe for your
own personal safety and to avoid damage to
property.
Symbols used:
c
This symbol is used as an addition
to the safety instructions and
warns of an electrical hazard.
m
This symbol is used as an addition
to the safety instructions and
warns of a potential hazard.
C
This symbol with the word
NOTE!
describes:
• Procedures that do not entail
any danger of injury.
• Important information,
procedures or handling steps.
Safety instructions are highlighted with
a warning triangle and shown as follows,
depending on the degree of hazard:
m
DANGER!
Indicates an immediately
threatening hazard that leads to
serious or even fatal injuries.
m
WARNING!
Indicates a potentially hazardous
situation that could lead to
serious or even fatal injuries.
m
CAUTION!
Indicates a potentially hazardous
situation that could lead to minor
injuries or damage to property.
Measures for safety
When operating electrical devices certain parts
of these devices inevitable carry dangerous
voltages. This could result in serious bodily
injury or damage to property if not handled
properly:
• Before establishing electrical connections
to the device, earth it at the ground wire
connection if there is one.
• Hazardous voltages may arise in all circuit
parts that are connected to the power supply.
• Even after disconnecting the supply voltage,
there may still be hazardous voltages
present in the device (capacitor storage).
• Do not operate equipment with current
transformer circuits when open.
• Do not exceed the limit values stipulated in
the user manual and on the rating plate - even
during testing or commissioning.
• Observe the safety and warning information in
the documents that belong to the devices!
Qualified personnel
In order to avoid injuries to personnel and
property damage, only qualified personnel with
electrical training are permitted to work on the
devices with knowledge
• of the national regulations for accident
prevention
• of safety standards
• of installation, commissioning and operation
of the device.
Proper use
The device is
• intended for installation in switch cabinets
and small installation distributors (please
observe step 3 “Assembly”).
• not intended for installation in vehicles!
The use of the device in mobile equipment
is considered to be non-standard
environmental conditions and is therefore
only permitted after separate agreement.
• not intended for installation in environments
with hazardous oils, acids, gases, vapours,
dusts, radiation, etc.
The prerequisites of faultless, safe operation
of this device are proper transport and proper
storage, set-up, installation, operation and
maintenance.
C
NOTE!
If residual currents in electrical systems
are monitored, the device (inputs I5/I6)
can trigger warning pulses if a response
threshold is exceeded. The warning pulses
can provide an alarm before a protective
device trips.
The device does not provide protection
against electric shock!
m
CAUTION!
Damage to property due to
disregard of the installation
instructions
Disregard of the installation instructions can
damage or destroy your device.
Ensure that you have enough air circulation
in your installation environment and in the
event of high environmental temperatures,
provide cooling if necessary.
Brief description of device
Assembly
Connecting the supply voltage
The supply voltage level for your device is
specified on the rating plate.
After connecting the supply voltage, an indication
appears on the display. If no indication appears,
check whether the supply voltage is within the
rated voltage range.
N
L
Fig. Connection of supply voltage.
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Device inputs that are dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
m
CAUTION!
Damage to property due to
disregard of the connection
conditions or impermissible
overvoltage!
Your device can be damaged or destroyed
by a failure to comply with the connection
conditions or by exceeding the permissible
voltage range.
Before connecting the device to the supply
voltage, please check:
•
Voltage and frequency correspond to the
details on the ratings plate! Limit values
stipulated in the user manual have been
complied with!
•
In building installations, the supply
voltage must be protected with a UL/IEC
approved circuit breaker / a fuse!
•
The isolation device
-
must be installed near the device and
in a location that is easily accessible
for the user.
-
must be labelled to identify the
respective device.
•
Do not tap the supply voltage from the
voltage transformer.
•
Provide a fuse for the neutral conductor
if the neutral conductor terminal of the
source is not grounded.
Mains systems
Three-phase, four-conductor system
with earthed neutral conductor
Three-phase, four-conductor system
with non-earthed neutral conductor
(IT networks)
Three-phase, three-conductor systems
Non-earthed
Three-phase, three-conductor systems
With earthed phase
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-N
/ U
L-L
277 VLN / 480 VLL
U
L-L
480 VLL
U
L-L
240 VLL
Single-phase, two-conductor systems
with earthed neutral conductor
Separated single-phase,
three-conductor systems
with earthed neutral conductor
The device can be used in
• 2, 3 and 4 conductor
networks (TN, TT and
IT networks)
• residential and
industrial applications.
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
L1
L2
L3
E
E
N
E
L1
L2
L3
E
N
R
L1
L2
L3
E
E
L1
L2
E
E
L
N
E
E
L1
L2
L3
E
E
L1
L2
N
E
E
U
L-N
230 VLN
U
L-N
/ U
L-L
240 VLN / 480 VLL
Voltage measurement
The device has 3 voltage measurement inputs
and is suitable for various connection variants,
with direct connection or via voltage transformer.
m
CAUTION!
Danger of injury or damage to
the device
Disregard of the connection conditions for the
voltage measurement inputs can result in injuries
or to the device being damaged.
For this reason, note that:
•
The voltage measurement inputs
-
are not connected to DC voltage.
-
are equipped with a suitable, labelled
fuse and isolation device located in
the vicinity (alternative: circuit breaker)
located nearby.
-
are dangerous to touch.
•
Voltages that exceed the allowed network
rated voltages must be connected via
a voltage transformer.
•
Measured voltages and measured currents
must derive from the same network!
L2
L3
N
L1
Connection variant
3p 4w
Voltage measurement
(Addr. 509 = 0, standard setting)
Fuse (UL/IEC listed)
Current measurement I1, I2, I3
Connection variants for voltage measurement
3p 4w
(Addr. 509 = 0, standard setting)
3p 4wu
(Addr. 509 = 1)
3p 4u
(Addr. 509 = 2)
3p 2u
(Addr. 509 = 5)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measurement with 3 phase
conductors and neutral conductor.
Measurement via voltage
transformer with 3 phase
conductors and neutral conductor.
Measurement with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
Measurement via voltage
transformer with 3 phase
conductors without neutral
conductor. Measured values which
require an N, use a calculated N.
1p 2w1
(Addr. 509 = 4)
2p 4w
(Addr. 509 = 3)
1p 2w
(Addr. 509 = 6)
3p 1w
(Addr. 509 = 7)
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Measured values derived from
voltage measurement inputs V2
and V3 are taken to be 0 and are
not calculated.
System with equal loading of the
phases. The measured values of
the voltage measurement input V2
are calculated.
TN-C system with 1-phase, three-
conductor connection. Measured
values derived from voltage
measurement input V3 are taken to
be 0 and are not calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Connection variant
3p 4w Current measurement
(I1, I2, I3) via current transformer
(Addr. 510 = 0,
standard setting).
c
WARNING!
Danger of injury due to
electrical voltage!
Serious bodily injury or death can result from:
• Contact with bare or stripped live wires.
• Current measurement inputs on the device
and on the current transformer that are
dangerous to touch.
Render the system free of voltage before
starting work! Check the system is free of
electrical energy!
Earth your system! Use the earth connection
points with earthing symbols for this!
Earth the secondary windings of current
transformers and all of the metal parts of the
transformer that could be touched!
C
NOTE!
If the measurement range is exceeded,
the measurement device display shows
"EEE"
. Further information on this can
be found in the user manual.
Connection variants for current measurement I1, I2, I3
3p 2i
(Addr. 510 = 1)
3p 2i0
(Addr. 510 = 2)
3p 3w3
(Addr. 510 = 3)
3p 3w
(Addr. 510 = 4)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
measured.
The measured values for current
measurement input I2 are
calculated.
Measurement in the 3-phase
network with unequal loading.
Measurement in the 3-phase
network with equal loading. The
measured values for current
measurement inputs I2 and I3 are
calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
2p 4w
(Addr. 510 = 5)
1p 2i
(Addr. 510 = 6)
1p 2w
(Addr. 510 = 7)
3p 1w
(Addr. 510 = 8)
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
System with equal loading of the
phases. The measured values for
current measurement input I2 are
calculated.
Measured values derived from
current measurement input I3
are taken to be 0 and are not
calculated.
Measured values derived from
current measurement inputs I2 and
I3 are taken to be 0 and are not
calculated.
3 systems with equal loading of
the phases. The measured values
of the unconnected phases (L2/
L3, L1/L3, L1/L2), of the respective
systems are calculated.
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
L1
L2
L3
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
I1
I2
I3
L1
L2
L1
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
N
I1
I2
I3
L1
L2
L3
I1
I2
I3
L1
L2
L3
L1
L2
L3
Current measuring I4
Analogue inputs
Connection variant for current
measurement (I4) via current
transformer
Current values but not power
values can be calculated for
current measurement input I4.
Load
The device has 2 analogue inputs
(terminals 32 to 37), each for a
• temperature measurement or
• residual current monitoring.
Use of the analogue inputs:
Measurement Terminal
Temperature
32/34 input 1
35/37 input 2
Residual
current
32/33/34 input 1
35/36/37 input 2
C
NOTE!
The measurement input I4 does not
require address setting on the device.
c
CAUTION!
Damage to the device / your
system due to short circuit
Inadequate insulation of the operating
equipment on the analogue inputs relative
to the mains supply circuits can lead to your
device/system being damaged.
Ensure that there is reinforced or double
insulation to the mains supply circuits!
C
NOTE!
Further information on current data and
current transformer data can be found
in the user manual.
Residual current monitoring (RCM) via I5 and I6
The UMG 96RM-E is suitable for use as a resid-
ual current monitoring device (RCM) as well as
for monitoring
• AC
• pulsing DC, and
• DC.
The UMG 96RM-E measures residual currents
in accordance with IEC/TR 60755 (2008-01),
type A and
type B.
Suitable residual current transformers with
a rated current of 30 mA are connected to
terminals 32 to 34 (
I5) and terminals 35 to
37 (
I6).
C
NOTE!
• The transformation ratios for the
residual current transformer inputs
can be individually configured via
the software.
• A connection variant
"UMG 96 RM-E with residual cur-
rent monitoring via measurement
inputs I5/I6" can be found in the
user manual.
• Measurement inputs I5 and I6 do
not require address setting on the
device.
3.
PC
UMG 96 RM-E
Ethernet
(crossover patch cable)
PC and UMG 96 RM-E require a fixed IP address..
1.
2.
DHCP server automatically assigns IP addresses to UMG 96 RM-E
and PC.
Ethernet
Ethernet
DHCP-
Server
PC
UMG 96 RM-E
Switch/
Router
(gedrehtes Patchkabel)
PC
RS232 RS232
RS485
RS485
UMG 96 RM-E
UMG 96 RM-E
Connection of the UMG 96 RM-E
via interface converter.
RS485
(gedrehtes Patchkabel)
PC
UMG 96 RM
UMG 96 RM
4.
UMG 96 RM-E
Connection of the UMG 96 RM via
an UMG 96 RM-E as gateway.
Ethernet
RS485
RS485
Establish connection to PC
The 4 most common connections for
communication between PC and device:
More details on device configuration and
communication can be found in section 14.
Recommendation for the Ethernet connection:
Use at least a CAT5 cable!
m
CAUTION!
Property damage due to
incorrect network settings
Incorrect network settings can cause faults in
the IT network!
Find out the correct Ethernet network
settings for your device from your network
administrator.
Controls and button functions
The UMG 96 RM-E is operated with buttons 1 and
2, whereby the following distinctions are made:
• Short press (button 1 or 2):
Next step (+1).
• Longer press (button 1 or 2):
Previous step (-1).
The device differentiates between display and
programming mode.
Measured values are arranged in measured value
display profiles and can be conveniently adapted
in the GridVis® software. Measured value display
profile 1 is configured at the factory.
Display mode
• Buttons 1 and 2 can be used to scroll between
the measured value indications.
• The measured value indication shows up to
3 measured values.
• A time for the automatic display change
between the measured value indications can be
configured in the GridVis® software.
C
NOTE!
More detailed information on operation, display and button functions for your device can be
found in the user manual.
Fig. UMG 96 RM-E display
Button 1
Button 2
Delivery
Mean value
CT: Current transformer
VT:
Voltage transformer
K1: Output 1
K2: Output 2
Password
Phase conductor-
Phase conductor
Summation measurement
Programming mode
Min. value NT/delivery
Max. value, HT/reference
• Hold buttons 1 and 2 depressed simultaneously
for 1 second to change between
display
mode
and
programming mode
. The text
PRG
appears in the display.
• Configure the necessary settings for the
operation of the device in programming mode.
• The programming mode can be protected with
a user password.
• Button 2 switches between the programming
menus:
1. Current transformer
2. Voltage transformer
3. Parameter list
4. TCP/IP device address
5. Subnet mask
6. Gateway address
7. Dynamic TCP/IP addressing (in/out)
The device switches from
programming mode
to
display mode
, if
• there is no button activity for 60 seconds.
• buttons 1 and 2 are pressed simultaneously for
1 second.
C
NOTE!
Changes are only applied after exiting the
programming mode.
C
NOTE!
The most important programming menus
for a quick start: TCP/IP device address,
subnet mask, gateway address (4th, 5th,
6th) and dynamic TCP/IP addressing
(on/off) (7th) via the Ethernet interface,
are explained here.
More detailed information on the
programming mode and interfaces can
be found in the user manual for the
device.
Programming mode
Example settings are selected for the device and
the PC to implement the following setttings:
Device IP address: 192.168.1.116
Subnet mask:
255.255.255.0
PC IP address:
192.168.1.117
Subnet mask:
255.255.255.0
C
NOTE!
The device is
factory-set to dynamic IP
allocation (
on) (DHCP mode).
Programming current transformers
1. Switch to programming mode.
2. The symbols for Programming mode
PRG,
and for the current transformer
CT appear.
3. Press button 1 - the first digit of the input
field for the primary current flashes.
4. Use button 2 to select the value of the
1st. digit.
5. Use button 1 to change to the 2nd. digit.
6. Use button 2 to select the value of the
2nd. digit.
7. Use button 1 to change to the 3rd. digit.
8. Use button 2 to select the value of the
3rd. digit.
9. Confirm with button 1.
10. The complete number flashes.
11. Use button 2 to select the decimal place and
thus the unit of the primary current.
12. Confirm with button 1.
13. The input range of the secondary current
flashes.
14. Set the secondary current (value 1 A or 5 A)
with button 2.
15. Confirm with button 1.
16. Exit programming mode by simultaneously
pressing buttons 1 and 2 (1 sec.). Use
button 2 to change to the input field for the
voltage transformer.
C
NOTE!
• Changes are only applied after exiting
the programming mode.
• Further information on current
transformers and current transformer
ratios can be found in the user manual.
C
NOTE!
Programming voltage transformers:
• Change to programming mode for the
voltage transformer.
• The symbols
PRG and VT appear in
the display.
• The procedure for the
voltage
transformer programming is analogous
to that of the current transformer.
Further information on voltage transformers
and voltage transformer ratios can be found
in the user manual.
Current transformer
symbol
Unit indicator
Current transformer,
primary
Programming mode
Current transformer,
secondary
Fig. "Current transformer" input field
Manual TCP/IP configuration via the Ethernet interface
Within an Ethernet network, each device has a unique
TCP/IP address that can be assigned manually or from
a DHCP server.
The 4-byte-long device address (Byte 0 to 3) is
appended within the TCP/IP configuration with the
subnet mask and gateway details.
Manual configuration (example) of the TCP/IP
device address (Addr):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and for
the current transformer
CT appear.
3. Pressing button 2 three times takes you to the
TCP/IP settings.
(Subnet mask, press
4x, gateway 5x)
4. Use button 1 to select the 1st. digit of Byte 0
(selection flashes).
5. Use button 2 to select the value.
6. Use button 1 to change to the 2nd. digit / 3rd. digit
7. Use button 2 to select the corresponding value.
8. Use button 1 to change to Byte 1
9. Select Bytes 1 to 3 in the same way.
10. Configure the subnet mask (display
SUb) and
gateway address (display
GAt) in the same way.
Designation
Byte identifier
of the address (e.g. Byte 0)
Address value, Byte 0
Fig. TCP/IP address
Byte 2, value 001.
Fig. TCP/IP address
Byte 3, value 116.
Fig. TCP/IP address,
Byte 1, value 168.
A TCP/IP address consists
of 4 bytes with the following
structure (example):
xxx.xxx.xxx.xxx
Byte 1
Byte 0
Byte 2 Byte 3
192.168.001.116
C
NOTE!
To ensure that a DHCP server does not overwrite the manual TCP/IP configuration,
deactivate
the dynamic IP allocation (dYn,
"oFF"
) (see steps 14 and 17). Then exit programming mode and
configure the TCP/IP address manually.
Dynamic TCP/IP allocation via the Ethernet interface (DHCP mode)
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address activated
(
Standard setting)
Fig. Gateway (
GAt),
Byte 0, value 192
Fig. Subnet mask (
SUb),
Byte 0, value 255
Fig. Dynamic assignment
(
dYn IP) of the
TCP/IP address deactivated
With dynamic TCP/IP allocation (TCP/IP device
address, subnet mask and gateway addresses)
a network incorporates the device automatically
when the device starts up.
The reading out (or the allocation) of the dynamic
TCP/IP settings is implemented in the same way as
the "manual configuration" (see also step 16):
1. Switch to programming mode.
2. The symbols for programming mode
PRG, and
for the current transformer
CT appear.
3. Pressing button 2
six times takes you to the
dynamic TCP/IP allocation (
dYn IP).
4. Press button 1 to activate the display
"on" or
"off" (display flashes).
5. Use button 2 to select
"on" or "off".
6. Confirm your selection using the 1 button.
7. Exit programming mode by pressing buttons 1
and 2 simultaneously for 1 sec.
The dynamic IP allocation can be implemented via
the software.
NOTE!
The key symbol on the display indicates
that dynamic TCP/IP allocation is active
(
on). When the device starts up, the
DHCP server automatically allocates the
TCP/IP device address, subnet mask
and gateway address.
Fig. Mounting position,
rear view
C
NOTE!
For further information on device functions, data and assembly, see the user manual.
Suitable network systems and maximum rated voltages (DIN EN 61010-1/A1):
Fuse
Circuit breaker
C
NOTE!
As an alternative to the fuse and circuit
breaker, you can use a line safety switch.
Circuit breaker
C
NOTE!
If the metering range is exceeded, the
measurement device display shows
"EEE"
. For further information, see the
user manual.
c
WARNING!
Risk of injury due to
large currents and high
electric voltages!
Current transformers that are operated open in the
secondary side (high voltage peaks) can cause
severe bodily injuries or death.
Avoid operating current transformers when open,
short circuit transformers that are unloaded!
The voltage measurement inputs are designed for
measurements in low voltage networks, in which
rated voltages of up to
• 277 V phase to earth and 480 V phase to phase
in the 4-conductor system or
• 480 V phase to phase in the 3-conductor system
occur.
The measurement and surge voltages meet
overvoltage category 300 V CATIII.
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
L2
L3
V1
V2
V3
V
N
L1
N
V1
V2
V3
V
N
L1
L2
V1
V2
V3
V
N
L1
L2
L3
N
V1
V2
V3
V
N
L1
L2
L3
L1
L2
L3
L1
L2
L3
V1
V2
V3
V
N
N
Art. Nr
. 33.03.220
Technical data
Voltage measurement
3-phase, 4-conductor systems
with rated voltages up to
277 V/480 V (+-10%)
3-phase, 3-conductor sys-
tems, unearthed, with rated
voltages up to
IT 480 V (+-10%)
Overvoltage category
300 V CAT III
Rated surge voltage
4 kV
Protection of
voltage measurement
1 - 10 A
(With IEC / UL approval)
Measurement range L-N
0
1)
to 300 Vrms
(max. overvoltage 520 Vrms )
Measurement range L-L
0
1)
to 520 Vrms
(max. overvoltage 900 Vrms )
Resolution
0.01 V
Crest factor
2.45 (related to the measurement range)
Impedance
4 MOhm / phase
Power consumption
approx. 0.1 VA
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Frequency range of
the fundamental oscillation -
resolution
45 Hz to 65 Hz
0.01 Hz
1) ... The device determines measured values only if the Voltage
measurement input V1 voltage L1-N greater than 20 Vrms
(4-wire measurement) or a voltage L1-L2 of larger 34 Vrms
(3-wire measurement) is applied.
Current measurement I1 - I4
Nominal current
5 A
Measurement range
0 - 6 Arms
Crest factor
1.98
Resolution
0.1 mA (display 0.01 A)
Overvoltage category
300 V CAT II
Rated surge voltage
2 kV
Power consumption
approx. 0.2 VA (Ri = 5 mΩ)
Overload for 1 sec.
120 A (sinusoidal)
Sampling rate
21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
for each measurement channel
Residual current monitoring I5 / I6
Nominal current
30 mArms
Measurement range
0 - 40 mArms
Triggering current
50
µ
A
Resolution
1
µ
A
Crest factor
1.414 (related to 40mA)
Burden
4 Ohm
Overload for 1 sec.
5 A
Sustained overload
1 A
Overload for 20 ms
50 A
C
NOTE!
Further technical data can be found in the
user manual for the device.
Supply voltage
Nominal range
Option 230 V:
AC 90 V - 277 V (50/60 Hz) or
DC 90 V - 250 V, 300 V CATIII
Option 24 V:
AC 24 V - 90 V (50/60 Hz) or
DC 24 V - 90 V, 150 V CATIII
Operating range
+-10% of the nominal range
Power consumption
Option 230 V: max. 7,5 VA / 4 W
Option 24 V: max. 7,5 VA / 5 W
Internal fuse,
not replaceable
Type T1A / 250 VDC / 277 VAC
according to IEC 60127
Recommended over-
current protection device for
the line protection
Option 230 V: 6-16 A
Option 24 V: 1-6 A
(Char. B)
(IEC/UL approval)
General information
Net weight
(with attached connectors)
approx. 370 g
Packaging weight
(including accessories)
approx. 950 g
Battery
Lithium battery CR2032,
3 V (approval i.a.w. UL
1642)
Service life of
background lighting
40000 h
(after this period of time
the background lighting
efficiency will reduce by
approx. 50%)
Transport and storage
The following information applies to devices which are trans-
ported or stored in the original packaging.
Free fall
1 m
Temperature
K55 (-25° C to +70° C)
Relative humidity
0 to 90% RH
Ambient coditions during operation
The device is intended for weather-protected, stationary use.
Protection class II i.a.w. IEC 60536 (VDE 0106, Part 1).
Operating temperature range
K55 (-10° C .. +55° C)
Relative humidity
0 to 75% RH
Operating altitude
0 .. 2000 m above sea level
Degree of pollution
2
Mounting position
vertical
Ventilation
Forced ventilation is
not required.
Protection against ingress
of solid foreign bodies and
water
- Front side
- Rear side
- Front with seal
IP40 i.a.w. EN60529
IP20 i.a.w. EN60529
IP54 i.a.w. EN60529
Digital inputs
3 optional digital inputs, semiconductor relays,
not short-circuit proof.
Maximum counter frequency
20 Hz
Input signal present
18V .. 28 V DC
(typical 4 mA)
Input signal not present
0 .. 5 V DC,
current less than 0.5 mA
Digital outputs
2 and 3 optional digital outputs, semiconductor relays, not
short-circuit proof.
Switching voltage
max. 33 V AC, 60 V DC
Switching current
max. 50 mAeff AC/DC
Response time
10/12 p 10 ms *
Pulse output (energy pulse)
max. 50 Hz
* Response time e.g. at 50 Hz: 200 ms + 10 ms = 210 ms
Temperature measurement input
2 optional inputs.
Update time
1 second
Connectable sensors
PT100, PT1000, KTY83,
KTY84
Total burden ( cable)
max. 4 kOhm
Cable length (digital inputs and outputs,
temperature measurement input)
Up to 30 m
Unshielded
More than 30 m
Shielded
Serial interface
RS485 - Modbus RTU/Slave
9.6 kbps, 19.2 kbps,
38.4 kbps, 57.6 kbps,
115.2 kbps
Stripping length
7 mm
Ethernet connection
Connection
RJ45
Terminal connection capacity (power supply voltage)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26 - 12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (residual current or
temperature measurement inputs and digital inputs /
outputs)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28-16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (current measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.2 - 2.5 mm
2
, AWG 26-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Terminal connection capacity (serial interface)
Single core, multi-core,
fine-stranded
0.2 - 1.5 mm
2
, AWG 28 - 16
Terminal pins, core end sheath
0.2 - 1.5 mm
2
Tightening torque
0.2 - 0.25 Nm
Stripping length
7 mm
Terminal connection capacity (voltage measurement)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
fine-stranded
0.08 - 4.0 mm
2
, AWG 28-12
Terminal pins, core end sheath
0.2 - 2.5 mm
2
Tightening torque
0.4 - 0.5 Nm
Stripping length
7 mm
Procedure in the event of faults
Possible fault
Cause
Remedy
No display
External fusing for the power supply voltage has
tripped.
Replace fuse.
No current display
Measurement voltage is not connected.
Connect the measuring-circuit voltage.
Measurement current is not connected.
Connect measuring-circuit current.
Current displayed is too large
or too small.
Current measurement in the wrong phase.
Check connection and correct if necessary.
Current transformer factor is incorrectly programmed. Read out and program the current transformer trans-
formation ratio at the current transformer.
The current peak value at the measurement input
was exceeded by harmonic components.
Install current transformer with a larger transforma-
tion ratio.
The current at the measurement input fell short of.
Install current transformer with a suitable transfor-
mation ratio.
Voltage displayed is too large
or too small.
Measurement in the wrong phase.
Check connection and correct if necessary.
Voltage transformer incorrectly programmed.
Read out and program the voltage transformer trans-
formation ratio at the voltage transformer.
Voltage displayed is too
small.
Overrange.
Install voltage transformers.
The peak voltage value at the measurement input has
been exceeded by harmonic components.
Caution! Ensure the measurement inputs are not
overloaded.
"EEE" in the display
See „error messages“ in the user manual.
"EEE bAt" in the display
Battery capacity is too low
Replace battery
(see "Replacing the battery" in the user manual).
Device still does not work
despite the above measures.
Device defective.
Send the device to the manufacturer for inspection
and testing along with an accurate fault description.
