Page 10
ENGLISH
Jandy
®
Laminar Jet | Installation and Operation Manual
Black
White
Green
Ground
Neutral
120 VAC
Power Supply
Black
White
Green
JUNCTION
BOX
Laminar Jet
with
LED Light
120V/12V
Transformer*
Black
White
Green
*Transformer must be supplied by a GFCI if required
by the transformer manufacturer's instructions, or by
local code and AHJ requirements
Figure 7. 12-Volt Laminar Jet with LED Light
Wiring Diagram
Clock
Motor
Ground
Ground
Neutral
Line
A
1
2
Black
White
Green
120 V SUPPL
Y
Black
White
Green
JUNCTION
BOX
Laminar Jet
with
LED Light
120V/12V
Transformer*
Black
White
Green
*Transformer must be supplied by a GFCI if required
by the transformer manufacturer's instructions, or by
local code and AHJ requirements
Figure 8. Wiring the Laminar Jet with LED Light
to a Time Clock
Ground
Neutral
Line
120 V Supply
Black
White
Green
SWITCH
Black
White
Green
JUNCTION
BOX
Laminar Jet
with
LED Light
120V/12V
Transformer*
Black
White
Green
*Transformer must be supplied by a GFCI if required
by the transformer manufacturer's instructions, or by
local code and AHJ requirements
Figure 9. Wiring the Laminar Jet with LED Light
to a Switch
4.3 Wiring Options for Controlling
Laminar Jet with LED Lights
NOTE:
The laminar jet with LED lights will not operate
properly with light dimmers. Do not wire the
laminar jet with LED lights to any dimming
circuitry.
To the extent allowed by code and capacity of the
To the extent allowed by code and capacity of the
electrical equipment, multiple laminar jets with LED
electrical equipment, multiple laminar jets with LED
lights may be controlled with a single switch so their
lights may be controlled with a single switch so their
colors will
colors will
always
always
be synchronized.
be synchronized.
Separate switches may be used to control the on/off
Separate switches may be used to control the on/off
and color functions of each laminar jet with LED light.
and color functions of each laminar jet with LED light.
It is recommended that these switches be located next
It is recommended that these switches be located next
to each other to facilitate simple color synchronization
to each other to facilitate simple color synchronization
when desired. All switches must be operated at the same
when desired. All switches must be operated at the same
time to assure color synchronization
time to assure color synchronization
..
Otherwise, the
Otherwise, the
lights will work independently of each other.
lights will work independently of each other.
4.3.1 Wiring to an AquaLink
®
RS
Control System
The laminar jet with LED light can be wired into
the Jandy AquaLink RS control system to provide
simplified operation of the lights, as well as a means
to synchronize the color change function. Connect the
laminar jet with LED lights to one of the auxiliary relays
in the Power Center.
NOTE:
It is recommended to connect one (1) laminar
jet with LED light per relay so each light can be
controlled separately. However, up to four (4)
laminar jets with LED lights can be connected
on a single relay. If there are more than four (4)
lights installed on one (1) AquaLink RS system,
ensure there is more than one (1) auxiliary relay
available in the Power Center.
Connect the laminar jet with LED lights to the power
center.
NOTE:
The laminar jet with LED light operates only
on 12 volts AC. A suitable 120-volt/12-volt
stepdown AC transformer MUST be used.
Read further for more important details.
4.3.2 Wiring to a Time Clock
The laminar jet with LED lights can be wired into a
basic time clock to automatically turn on the laminar jet
with LED lights at a predesignated time. Connect the
laminar jet with LED lights into the time clock.
4.3.3 Wiring to a Switch
The laminar jet with LED lights can be wired into a
switch to manually turn on/off the lights. Connect the
laminar jet with LED lights into the switch.