background image

SECTION 3. Installation Instructions

6

3.4  Clamp Installation, DEL Series

1. Be certain the o-ring is in position in the lower tank 
half. Press the filter lid over the lower half sandwiching 
the o-ring between the two halves.

2.  Holding  the  ends  of  the  filter  clamp  apart,  position 
the hinged segment of the filter clamp over both upper 
and  lower  tank  flanges.  Bring  the  ends  of  the  filter 
clamp together.

3.  Place  the  "T"  nut  and  threaded  rod  assembly  into 
the clamp. Besure the "T" nut is seated in the clamp in 
the proper orientation (See Fig. 6).

4.  Use  a  9/16"  socket  on  the  tightening  nut  until  the 
clamp ring halves touch each other, or are within 1/16" 
(See  Fig.  6)  but  do  not  overtighten  as  the  clamp  can    
break. If unable to tighten as indicated, do not operate   
the filter and call a service technician immediately.

5.  After  the  first  week  of  operation,  check  the  clamp 
and retighten if necessary.

6. Check the filter clamp at least once a month. 

                              WARNING

Follow  these  instructions  carefully.  Improper       
clamp  installation  can  cause  the  filter  lid  to  be      
blown  off  which  can  result  in  death,  serious 
personal injury or property damage.

"T" Nut and
Threaded Rod

Tightening Nut
w/ Shoulder

Clamp Ring

Figure 5- Filter Clamp Ring

Figure 6- Filter Clamp Ring Assembly

"T" Nut

Threaded
Rod

Tightening
Nut w/
Shoulder

Tightening
Nut w/
Shoulder

Clamp Ring

Use a 9/16" Socket 

Clamp Ring, Closed Position

GAP NOT TO
EXCEED 1/16"

Summary of Contents for DEL Series Filters
















Reviews: