background image

2

With the setting above, the circulation pump will work automatically.

3

)、

If the temperature is set at 3

5℃,

 when the water temperature reaches or exceeds 3

6℃,

 the heater

will be turned off automatically and the circulation pump will stop after 5 seconds. When the water temperature
reaches or is lower than 3

4℃,

 the heater will start up again.

4

)、

In the case of an error the LCD shows ”E1”.  If this happens, the thermostatic heating system will

NOT be available, the heater doesn’t work.

15

Operating the Air Blower

Press

 controls the blower.

16

Fahrenheit & Celsius Temperature shift

In the status of

Power off

 pressing the key

 “

” can change the mode of 

Fahrenheit & Celsius degree.

 

17

When there is no water in the spa. All water pumps and heating system can not start up. However the

corresponding signals will flash on the LCD.

18

Prevent freezing function:

The heater & circulation pump will work automatically once the water temperature is below 

5℃,

 when the water

temperature is reach at  10 ,  heating will stop. This function is only available while the spa is on normal power

supply.

IV

Electric parameters

1

Performance index

Rated voltage

 220V/50Hz                        

Maximum working current

60 A/220

V-240V~

Voltage-resistance

1250V/1

 minute without penetration

     

Isolative resistance

:》

10MΩ

Water resistance grade

IPX5                             

Electric shock resistance

first grade

(2) Output loading index

Heater

 AC220V/3KW x 1                          Surf Water pump

 AC220V/3 HP x 1

water pump

 

 AC220V/2H

P x 2                     pump

AC220v/1HP x 1

Air pump

 AC220V/0.7kw x 1  

spa light

 AC12V/5W x 1                         Ozone

Ozone

 12

V

/15

W×1

water Radio

1) Frequency Range

 FM

 87.0~108.0MHz

        2) Maximum Output Power

 10W

3) Speaker

8Ωdamp proof speaker

5.Warning Information

a.

       

Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

b.

       

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 

qualified persons in order to avoid a hazard.

c.

       

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 
instruction concerning use of the appliance by a person responsible for their safety.

d.

       

Children should be supervised to ensure that they do not play with the appliance.

10

Summary of Contents for SPA J-838
















Reviews: