Jammin X2 Pro Instruction Manual Download

Page: 6 / 38

OPTION THINGS NEED BESIDES THE KIT

RADIO CONTROL UNIT

12V Battery for Starter Box
(must have)

Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)

AA Batteries ( 12 pcs ) for radio

Note: Carefully read the instruction manual of your
2 channel radio controller before using.

Radio must be set at neutral position
before installing in the kit.

SEQUENCE TO SET NEUTRAL

Install AA batteries in Radio.

Extend the antenna.(Transmitter)

Install batteries into Car receiver .

After installing the battery, connect the
battery box.

Extend the antenna. (Receiver)

Set the trim-lever at center.

Turn on the switch. (Transmitter)

Turn on the switch. (Receiver)

Make sure the servos are in command.

When the operation stick is in neutral,
servo horns must be in neutral as well.
*Adjustment can be made by re-
installing the servo horn.

Turn off the switch. (Receiver)

Turn off the switch. (Transmitter)

Retract the antenna. (Transmitter)

THINGS REQUIRED FOR OPERATION

Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC

SUITABLE SERVO SIZE

29mm - 42mm

15mm - 21mm

- 1m

m 4

3.5 cc (21 Class) ENGINE

REAR EXHAUST

Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel

# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug

Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts

More Optional Parts . . .

#10201
1700 NimH Battery Hump
Pack .. $34.95

# 10214 NiMh Battery Pack
Charger.. $7.95

# 51007 or 08 OFNA/Picoo
Glow Plug .. $13.95

OPTION PART

JAMMIN .21JPX
PART # 51250
RETAIL 399.95

TOOLS NOT INCLUDED IN THE KIT

INCLUDED IN THE KIT

Phillips Type Screw Drivers ( L )

Phillips Type Screw Drivers ( S )

Cutter

Curved Scissors

Knife

Instant Cemment

Cross Wrench

Masking Tape

Paints

Brush

Precision Caliper

3000

5000

1000

Diff. Oil

Shock Oil

1.5mm Allen Wrench

2mm Allen Wrench

2.5mm Allen Wrench

4mm'5mm Allen Wrench

17mm Wheel Nut
Wrench

Needle Nosed Pliers

10244 TRUGGY / BUGGY
PRO STARTER BOX

Summary of Contents for X2 Pro







































Search results

Summary of Contents for X2 Pro

Reviews:

Related manuals for X2 Pro

Brands by name

Popular brands

Jammin X2 Pro, Instruction Manual

Search results

Summary of Contents for X2 Pro

Reviews:

Related manuals for X2 Pro

Brands by name

Popular brands