Jamie Oliver Explorer 5500, Assembly, Use & Care Manual

Page: 5 / 38

211116
EN
GAS CONNECTION
This is a limitative configured grill. Do not attempt to use other type gas supply unless the grill has
been reconfigured for other gas use. The installation of this appliance must conform to local codes.
Make sure that both gas cylinder and gas hose do not come in contact with high temperature part.
1. Make sure cylinder valve is in its full “O” position (turn clockwise to stop).
2. Check cylinder valve to assure it has proper external male threads.
3. Inspect valve connection port and regulator assembly. Look for any damage or debris. Remove
any debris. Inspect hose for damage. Never attempt to use damaged or plugged equipment.
4. When connect regulator assembly to the valve, hand tighten nut clockwise to a positive stop. Do
not use a wrench to tighten. Use of a wrench may damage quick coupling nut and result in a
hazardous condition.
5. Open cylinder valve fully (counterclockwise). Use a soapy water solution to check all connections
for leaks before attempting to light grill. If a leak is found, turn cylinder valve off and do not use grill
until a local gas dealer can make repairs.
„
Regulator and Hose Requirements:
1. Pressure regulator: comply with EN 16129 and comply with local code (Flow rate: max. 2 kg/h).
2.
Gas hose: comply with EN 16436-1 and local market standard. (max. 1.5m, max. FI 1.2m).
3. The type of flexible tube connecting the appliance to the gas cylinder and the length recommended
which shall not exceed 1,50 m.
4. Care should be taken so the gas hose and gas cylinder do not come in contact with hot surfaces
(above 140
℉
,60
℃）
or sharp edges, and should not pass under the barbecue
„
Gas Cylinder Requirements:
1. Always place gas cylinder on a flat level surface DO NOT fix on trolley.
2. Maximum Capacity Maximum 15 kg and comply with local codes.
3. Measurement: the height could not exceed 0.6m, the dia. of the gas cylinder should not exceed
320mm.
4. Make sure the gas cylinder is lower than the gas inlet connection and avoid touching with hot
surface.
5. The gas cylinder shall be 0.5m away from the appliance.
！！ ！
WARNING
！ ！！
1. DO NOT USE THE GRILL UNTIL LEAK TESTED.
2. Stop using and call the fire department if any leak detected.
3. Replacement hose assemblies must be those specified by the manufacturer.
4. Never insert any foreign objects into the valve outlet. It may damage the valve and cause leak, leaking gas
may result in fire, explosion, heavy body injury, or even death.
5. Do not connect this grill to the self-contained the gas system of a motor home or camper trailer.
6. If you cannot stop a gas leak, close the gas cylinder valve IMMEDIATELY; call the gas supplier or the fire
department.
7. Always turn off the gas cylinder and detach from the grill after use or before moving.
8. VERY IMPORTANT: DISCONNECTED THE CYLINDER WHEN THIS GRILL IS NOT IN USE.
„
Leak testing
1. Make sure all control knobs are closed.
2. Make sure the regulator is connected to the gas cylinder tightly and the cylinder is full.
3. Make a soap solution with one part liquid detergent and one part water. Prepare a spray bottle,
brush, or rag to apply the solution to the connections.
4. Completely open the cylinder valve by turning counter clockwise. If you hear a “POP” sound, turn
gas off IMMEDIATELY, it indicates a heavy leak at the connection. Call your gas dealer or fire
department.
5. Check every connection from the gas cylinder up to and including the connection to the manifold
pipe assembly (the pipe that goes to the burner) by brushing or spraying the soapy solution on
the connections.
6. If soap bubbles appear, there is a leak. Turn off the cylinder valve IMMEDIATELY and retighten
connections, Open the cylinder valve again, and recheck.
5